GE GE 31-30263 05-10 Connect Drain Line, Follow ALL Local Codes and Ordinances

Page 10

Installation Instructions

STEP 13 – CONNECT DRAIN LINE

FOLLOW ALL LOCAL CODES AND ORDINANCES.

The drain hose molded end will fit 5/8”,3/4”or 1” diameter connections on the air gap, waste tee or disposer . Cut on the marked line as required for your installation.

Cuting CuttingLines Lines

1" "4/3 "8/5

Figur e 20

IMPORIMPTAORNTA:DoNT:notDocutnotcorrugatedcut corrugated

portion of hose por tion of hose

‡,IDORQJHUGUDLQKRVHLVUHTXLUHGDGGXSWRµRIIOHQJWK for a total of 10ft. to the factory installed hose.

Use 5/8”or 7/8”inside diameter hose and a coupler to connect the two hose ends. Secure the connection with hose clamps.

DRAIN LINE INSTALLATION

‡&RQQHFWGUDLQOLQHWRDLUJDSZDVWHWHHRUGLVSRVHU using either previously determined method.

Method 1- Air gap with waste tee or disposer

Waste Tee Installation Disposer Installation Figure 22

Method 2- High drain loop with waste tee or disposer

Fasten to underside

Fasten to underside

of countertop

of countertop

 

32"

 

18"

Min.

18"

Min.

 

Min.

Hose Clamp

CoupCo ler

Hose Clamp

Waste Tee Installation

Disposer Installation

 

Figure 23

Hose Clamp

Figure 21

‡6HFXUHWKHGUDLQKRVHWRWKHDLUJDSZDVWHWHHRU disposer with clamps.

127(727$/'5$,1+26(/(1*7+0867127(;&((' )((7)253523(5'5$,123(5$7,21.

IMPORTANT -

When connecting drain line to disposer , check to be sure that drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE.

Remove Remove hopper Hopper

pPluglug

TIP: Avoid unnecessary service call char ges. Always be sure disposer drain plug has been removed before attaching dishwasher drain hose to the disposer .

10

Image 10
Contents Read these instructions completely and carefully More time than replacement installationsRead Carefully Keep These Instructions Read and observe all Cautions and WarningsMaterials YOU will Need Installation PreparationParts Supplied Tools YOU will NeedDrain Requirements Prepare Dishwasher EnclosureOr Method 2 may be used. or Figure Electrical Requirements Prepare Electrical WiringCabinet Preparation & Wire Routing 2 Dia Hole Max From Cabinet From Wall Ground BlackBefore YOU Begin Installation InstructionsPrepare HOT Water Line Check Door BalanceInstall Power Cord Installation InstructionAdjust Leveling Legs Install 90 ElbowSlide Dishwasher Partially Into Cabinet Position Water Line and House WiringInsert Drain Hose Through Cabinet ‡$V\RXSURFHHGSXOOWKHGUDLQKRVHWKURXJKWKHHecC k Levl Side To Side Turn Legs to Adjust Level DishwasherDishwasher must be secured to the countertop Secure Dishwasher to CabinetConnect Water Supply Countertop with the 2 Phillips screws providedConnect Drain Line Follow ALL Local Codes and OrdinancesTemperature. Incoming water temperature Must Connect Power SupplyPRE-TEST Checklist Be between 120 F and 150 F. a Minimum of 120 FReplace Toekick Dishwasher WET TestLiterature Instructions d’installation Lire Attentivement IL Faut Garder CES InstructionsPièces Fournies Préparation pour l’installationOutils Nécessaires Préparer L’ENCEINTE DU LAVE-VAISSELLE Spécifications DE VidangePréparation pour l’installation Alimentation électrique Préparation Pour LE Branchement ÉlectriqueAvant DE Commencer Préparation pour l’installation Alimentation d’eau chaudePréparation DE L’ALIMENTATION D’EAU Chaude ‡&RXSHUO·DOLPHQWDWLRQG·HDXÉtape 5 Installation DU Coude À Angle Droit Installation du lave-vaisselleÉtape 4 Installation DU Cordon D’ALIMENTATION Étape 2 Réglage DES Pieds DE Mise À NiveauÉtape 7 Insertion DU Tuyau DE Vidange Dans LE Placard 15 cm 6 po Fils de Tuyau la maison ’eauTr ou Étape 9 Positionnement DU LAVE-VAISSELLE Sous LE ComptoirÉtape 10 Mise À Niveau DU LAVE-VAISSELLE OT urner lesÉtape 11 Fixation DU LAVE-VAISSELLE AU Placard Ressort de porteÉtape 13 Raccordement DU Conduit DE Vidange Installation DU Tuyau DE VidangeInstallation avec un broyeur à déchets CollierBlanc Étape 15 Liste DE Vérification Avant DE Faire LES EssaisÉtape 14 Branchement DE L’ALIMENTATION Électrique TerreÉtape 17 Remise EN Place DE LA Plaque DU BAS Ajustez le haut Adjust Up Ou vers le bas or DownÉtape 16 Essai DU LAVE-VAISSELLE Avec DE L’EAU Étape 18 Documentation

GE 31-30263 05-10 specifications

The GE 31-30263 05-10 is a standout product in the realm of commercial and industrial motors, designed to deliver exceptional performance and efficiency. This model, manufactured by General Electric, is built to withstand rigorous operating conditions while providing reliable functionality across a range of applications.

One of the main features of the GE 31-30263 05-10 is its robust construction, which includes high-quality materials that ensure durability. The motor is engineered to handle varying load requirements, making it suitable for processes that demand consistent power output. Its design incorporates an efficient cooling system that prevents overheating during prolonged use, allowing it to maintain optimal operating temperatures even in high-demand settings.

Technologically, the GE 31-30263 05-10 is equipped with advanced motor control capabilities. It supports various control methods, including VFD (Variable Frequency Drive) compatibility, which enhances its versatility and adaptability to different industrial requirements. This feature allows users to precisely control the speed of the motor, leading to significant energy savings and greater operational efficiency.

Another noteworthy characteristic is the motor's low maintenance requirements. The GE 31-30263 05-10 is designed with features that minimize wear and tear, reducing the frequency and cost of repairs. This reliability translates to lower total cost of ownership, making it an attractive option for businesses looking to optimize their operational expenses.

In terms of efficiency, this motor operates at a high performance level, often exceeding industry standards for energy consumption. This makes it not only an environmentally friendly choice but also a financially wise investment, as it helps organizations reduce energy bills.

Overall, the GE 31-30263 05-10 is a versatile, durable, and efficient motor that stands out in the market. Its combination of advanced technology, robust build, and low maintenance needs positions it as an ideal solution for various industrial applications, from manufacturing to automation. Companies seeking a reliable motor for their operations will find that the GE 31-30263 05-10 meets and exceeds expectations, providing both performance and value.