GE GE 31-30263 05-10 installation instructions Dishwasher WET Test, Replace Toekick, Literature

Page 12

Installation Instructions

STEP 16 – DISHWASHER WET TEST

†Turn on power supply(or plug power cord into outlet, if equipped).

†Turn on Dishwasher

†6HOHFW´1RUPDOZDVKµSURJUDP

†Close the door. There will be a 5 second pause, followed by a 60 second pump-out.

†Check to be sure that water enters the dishwasher. If water does not enter the dishwasher,check to be sure that water and power are turned on.

†Check for leaks under the dishwasher. If a leak is found,turn power supply off, then tighten connections. Restore power after leak is corrected.

†Check for leaks around the door. A leak around the door could be caused by door rubbing or hitting against adjacent cabinetry. Reposition the dishwasher if necessary.See step 9.

†The dishwasher will drain about 12 minutes after the first fill. Check drain lines.If leaks are found,turn power off at the breaker and correct plumbing as necessary. Restore power after corrections are made. See Step 12.

†Open dishwasher door and make sure most of the water has drained.If not, check that disposer plug has been removed and/or air gap is not plugged. See Step 13. Also check drain line for kinking.

†Run the dishwasher through another fill and drain cycle. Check for leaks and correct if required.

STEP 17 – REPLACE TOEKICK

2-Screws

Adjust Up or Down

Install 2 toekick screws to fasten toekick. Allow the toe kick to tuch the floor.

STEP 18 – LITERATURE

Be sure to leave complete literature package and installation instructions with consumer.

127(7KHPDQXIDFWXUHUIROORZLQJDSROLF\RIFRQVWDQWGHYHORSPHQWDQGXSGDWLQJRIWKHSURGXFWPD\PDNH

modifications without giving prior notice.

12

Image 12
Contents More time than replacement installations Read Carefully Keep These InstructionsRead these instructions completely and carefully Read and observe all Cautions and WarningsInstallation Preparation Parts SuppliedMaterials YOU will Need Tools YOU will NeedPrepare Dishwasher Enclosure Drain RequirementsOr Method 2 may be used. or Figure Prepare Electrical Wiring Cabinet Preparation & Wire RoutingElectrical Requirements 2 Dia Hole Max From Cabinet From Wall Ground BlackInstallation Instructions Prepare HOT Water LineBefore YOU Begin Check Door BalanceInstallation Instruction Adjust Leveling LegsInstall Power Cord Install 90 ElbowPosition Water Line and House Wiring Insert Drain Hose Through CabinetSlide Dishwasher Partially Into Cabinet ‡$V\RXSURFHHGSXOOWKHGUDLQKRVHWKURXJKWKHHecC k Levl Side To Side Turn Legs to Adjust Level DishwasherSecure Dishwasher to Cabinet Connect Water SupplyDishwasher must be secured to the countertop Countertop with the 2 Phillips screws providedConnect Drain Line Follow ALL Local Codes and OrdinancesConnect Power Supply PRE-TEST ChecklistTemperature. Incoming water temperature Must Be between 120 F and 150 F. a Minimum of 120 FDishwasher WET Test Replace ToekickLiterature Instructions d’installation Lire Attentivement IL Faut Garder CES InstructionsPréparation pour l’installation Pièces FourniesOutils Nécessaires Préparer L’ENCEINTE DU LAVE-VAISSELLE Spécifications DE VidangePréparation pour l’installation Alimentation électrique Préparation Pour LE Branchement ÉlectriquePréparation pour l’installation Alimentation d’eau chaude Préparation DE L’ALIMENTATION D’EAU ChaudeAvant DE Commencer ‡&RXSHUO·DOLPHQWDWLRQG·HDXInstallation du lave-vaisselle Étape 4 Installation DU Cordon D’ALIMENTATIONÉtape 5 Installation DU Coude À Angle Droit Étape 2 Réglage DES Pieds DE Mise À NiveauÉtape 7 Insertion DU Tuyau DE Vidange Dans LE Placard 15 cm 6 po Fils de Tuyau la maison ’eauÉtape 9 Positionnement DU LAVE-VAISSELLE Sous LE Comptoir Étape 10 Mise À Niveau DU LAVE-VAISSELLETr ou OT urner lesÉtape 11 Fixation DU LAVE-VAISSELLE AU Placard Ressort de porteInstallation DU Tuyau DE Vidange Installation avec un broyeur à déchetsÉtape 13 Raccordement DU Conduit DE Vidange CollierÉtape 15 Liste DE Vérification Avant DE Faire LES Essais Étape 14 Branchement DE L’ALIMENTATION ÉlectriqueBlanc TerreAjustez le haut Adjust Up Ou vers le bas or Down Étape 16 Essai DU LAVE-VAISSELLE Avec DE L’EAUÉtape 17 Remise EN Place DE LA Plaque DU BAS Étape 18 Documentation

GE 31-30263 05-10 specifications

The GE 31-30263 05-10 is a standout product in the realm of commercial and industrial motors, designed to deliver exceptional performance and efficiency. This model, manufactured by General Electric, is built to withstand rigorous operating conditions while providing reliable functionality across a range of applications.

One of the main features of the GE 31-30263 05-10 is its robust construction, which includes high-quality materials that ensure durability. The motor is engineered to handle varying load requirements, making it suitable for processes that demand consistent power output. Its design incorporates an efficient cooling system that prevents overheating during prolonged use, allowing it to maintain optimal operating temperatures even in high-demand settings.

Technologically, the GE 31-30263 05-10 is equipped with advanced motor control capabilities. It supports various control methods, including VFD (Variable Frequency Drive) compatibility, which enhances its versatility and adaptability to different industrial requirements. This feature allows users to precisely control the speed of the motor, leading to significant energy savings and greater operational efficiency.

Another noteworthy characteristic is the motor's low maintenance requirements. The GE 31-30263 05-10 is designed with features that minimize wear and tear, reducing the frequency and cost of repairs. This reliability translates to lower total cost of ownership, making it an attractive option for businesses looking to optimize their operational expenses.

In terms of efficiency, this motor operates at a high performance level, often exceeding industry standards for energy consumption. This makes it not only an environmentally friendly choice but also a financially wise investment, as it helps organizations reduce energy bills.

Overall, the GE 31-30263 05-10 is a versatile, durable, and efficient motor that stands out in the market. Its combination of advanced technology, robust build, and low maintenance needs positions it as an ideal solution for various industrial applications, from manufacturing to automation. Companies seeking a reliable motor for their operations will find that the GE 31-30263 05-10 meets and exceeds expectations, providing both performance and value.