Maytag W10321480A installation instructions Base Grille Water Filtration System

Base Grille Water Filtration System

Model P1WG2L/P2RFWG2 Capacity 200 Gallons (757 Liters)

Model P1WG2/P2RFWG2 Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/ANSI

Standard 42 for the reduction of Chlorine Taste and Odor, Particulate

Class I*; and against NSF/ANSI Standard 53 for the reduction of Lead,

Mercury, Benzene, Toxaphene, and O-dichlorobenzene.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction	NSF Reduction	Average	Influent Challenge	Maximum	Average	Minimum %	Average %
Aesthetic Effects	Requirements	Influent	Concentration	Effluent	Effluent	Reduction	Reduction
Chlorine Taste/Odor	50% reduction	1.909 mg/L	2.0 mg/L ± 10%	0.05 mg/L	<0.05 mg/L	>97.4	>97.4
Particulate Class I*	85% reduction	5166666 #/mL	At least 10,000 particles/mL	4200 #/mL**	1900 #/mL	>99.9	>99.9
Contaminant	NSF Reduction	Average	Influent Challenge	Maximum	Average	Minimum %	Average %
Reduction	Requirements	Influent	Concentration	Effluent	Effluent	Reduction	Reduction
Lead: @ pH 6.5	0.010 mg/L	143.33 ug/L	0.15 mg/L ± 10%	1.0 ug/L	1.0 ug/L	>99.3	>99.3
Lead: @ pH 8.5	0.010 mg/L	150 ug/L	0.15 mg/L ± 10%	1.0 ug/L	1.0 ug/L	>99.3	99.3
Mercury: @ pH 6.5	0.002 mg/L	0.0058 mg/L	0.006 mg/L ± 10%	0.3 ug/L	0.0002 mg/L	94.8	96.4
Mercury: @ pH 8.5	0.002 mg/L	0.00646 mg/L	0.006 mg/L ± 10%	0.8 ug/L	0.0004 mg/L	88.5	94.9
Benzene	0.005 mg/L	0.015 mg/L	0.015 mg/L ± 10%	0.5 ug/L	0.0005 mg/L	>96.7	>96.7
O-Dichlorobenzene	0.6 mg/L	1.83333 mg/L	1.8 mg/L ± 10%	160 ug/L	0.005 mg/L	91.1	96.5
Toxaphene	0.003 mg/L	0.016 mg/L	0.015 mg/L ± 10%	1 ug/L	0.001 mg/L	>93.8	>93.8

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

■It is essential that operational, maintenance, and filter replacement requirements be carried out for the product to perform as advertised.

■Use replacement filter P2RFWG2, part #4396841.

2010 suggested retail price of $39.99 U.S.A./$54.95 Canada. Prices are subject to change without notice.

Model P1WG2L/P1WG2: Style 1 – When the filter indicator reads 10%, order a new filter. When the indicator reads 0%, it is recommended that you replace the filter.

Style 2 – When the filter indicator changes from green to yellow, order a new filter. When the indicator changes from yellow to red, it is recommended that you replace the filter.

Style 3 – When the water filter status display changes from “GOOD” to “ORDER,” order a new filter. When the filter indicator reads “REPLACE,” it is recommended that you replace the filter.

Style 4 – Press FILTER to check the status of your water filter. If the filter indicator light is yellow, order a new filter. If the filter indicator light is red, it is recommended that you replace the filter.

Change the water filter cartridge every 6 months. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter cartridge more often.

■These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary.

■The product is for cold water use only.

■Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

■Refer to the “Warranty” section for the Manufacturer’s name, address and telephone number.

■Refer to the “Warranty” section for the Manufacturer’s limited warranty.

Application Guidelines/Water Supply Parameters

Water Supply	City or Well
Water Pressure	30 - 120 psi (207 - 827 kPa)
Water Temperature	33° - 100°F (0.6° - 37.8°C)
Service Flow Rate	0.5 gpm (1.9 Lpm) @ 60 psi

*Class I particle size: >0.5 um to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust. ® NSF is a registered trademark of NSF International.

18