Fisher & Paykel OB24SDPX Timer, SEMI-AUTOMATIC Cooking, Setting, During cooking

Page 18

3

 

I

I

 

￿

I

I

 

 

I

 

 

 

 

I

 

1

 

5

6

TIMER

The timer function is only used to count the time and does not influence oven operation or any program which are in progress or set.

1.Press push button 1. The bell symbol will start to flash.

2.Press keys 5 or 6 to set the time required.

3.The countdown starts immediately. The bell symbol stops flashing and the time appears again.

4.To see the countdown press push button 1. The time will be indicated in hours and minutes; the seconds are only indicated for the last minute.

5.At the end of the countdown an audible signal sounds and the bell symbol on the display flashes.

Press any push button to stop the audible signal.

IMPORTANT WARNING: This function is only an electronic alarm and does not switch OFF the oven. Remember to turn OFF manually the selector knob at the end of the countdown.

SEMI-AUTOMATIC COOKING

Start immediate cooking and switch the oven off automatically after the programmed cooking time.

Setting

I

I

I

I

I

I

I

I

I

2

I

I

I

 

I

I

 

I

I

 

I

I

 

 

I

I

 

I

I

 

5

6

1.Set the cooking function by turning the oven selector to the function required.

2.The cooking temperature appears on the display. To change it proceed as described in the “Setting the cooking” section.

3.Press push button 2. AUTO starts to flash and 0.00 appears.

4.Press push buttons 5 or 6 to set the cooking time (cooking time in hours and min- utes: set it to ten minutes less than the time required because the stored heat will complete the cooking).

5.On the display AUTO becomes steady and the cooking program starts.

During cooking

6.During the cooking cycle, the display shows the oven temperature measured by the probe or pre-set temperature.

Press key 2 to display the time remaining until the end of cooking.

The cooking time and temperature can be varied at any time, as described above.

At the end of cooking

I

I

I

I

I

I

I

I

I

 

II

18

7.End appears on the display, AUTO flashes and the audible signal sounds. The cooking cycle has finished and the oven is OFF.

8.Press any program push button to stop the audible signal.

9.OFF appears (oven OFF).

10.Turn the function selector to 0 (OFF).

11.The program display shows the time.

Note: At the end of the program always turn the function selector knob to 0 (OFF).

Image 18
Contents Installation instructions and User guide Important Please Read and Follow Important Precautions and Recommendations Using the Oven for the First TimeControl panel How to use the self cleaning oven General FeaturesOven Light this is not a cooking function Defrosting Frozen Foods this is not a cooking functionConvection Cooking with Ventilation Ventilated Cooking with Double Broil BroilingVentilated Broiling Self Cleaning Function this is not a cooking function Important NotesSelecting F/C on the Display Turn the oven selector knob to a cooking function i.eSetting the Cooking only for the Cooking Functions Turn the selector knob to the cooking function required2a. If F or C is not flashing press key 4 of the program HOW to Start the Self Cleaning Cycle Door with Auto flashing Steady doorSounds for F0.00 with Auto flashingTurn the function selector to 0 OFF HOW to Stop the Self Cleaning CycleAccidental Interruption of the Self Cleaning Cycle Function selector has been turned to any cooking functionAbnormal Situations AND/OR Operation Problems During cooking or the self cleaning cycleF0.00 appears during the self cleaning cycle Cooking Different Dishes AT the Same Time Cooking Advice Sterilization Roasting Ventilated Broiling and AU GratinBroiling Setting the Time How to use the electronic programOn Switching on for the First Time or After a BLACK-OUT Audible SignalSEMI-AUTOMATIC Cooking TimerSetting During cookingAutomatic Cooking Starting cookingCancelling a SET Program Examplesof Programming Automatic CookingCleaning and maintenance Oven Shelf Installation and Removal Removing the Oven DoorReplacement Parts Electrical Grounding InstructionsElectrical Requirement Installation to the cabinet General Information23 5/8 min 600 mm min Connect with Copper Wire only Or If connecting to a four-wire electrical systemL1 L2 = L1 N L2 N Important Veuillez Lire ET Suivre Consignes ET Recommandations Importantes Utilisation DU Four Pour LA Première FoisTableau de commande Comment utiliser le four autonettoyant Caractéristiques GénéralesRemarques SUR LE Fonctionnement DU Four Il ne s’agit pas d’une fonction de cuisson Lampe DU Four il ne s’agit pas d’une fonction de cuissonDécongélation DES Aliments Cuisson À Convection Avec VentilationCuisson AU Gril Cuisson AU Gril VentiléeRemarques Importantes Sélection DE F/C SUR L’ÉCRAN D’AFFICHAGE Réglage DE LA Cuisson Seulement Pour LES Fonctions DE CuissonComment Démarrer L’AUTONETTOYAGE Pressez le bouton 3 du programmateur pour démarrer le cycleFait entendre pendant 30 secondes Door et Auto clignotentF0.00 et Auto clignotent Comment Arrêter L’AUTONETTOYAGE QUE Faire Lorsque LE Cycle D’AUTONETTOYAGE EST TerminéInterruption Accidentelle DU Cycle D’AUTONETTOYAGE Situations Anormales ET/OU Problèmes DE Fonctionnement Lors de la cuisson ou de l’autonettoyageF0.00 s’affiche lors de l’autonettoyage Cuisson Simultanée DE Plats Variés Conseils DE Cuisine StérilisationRôtissage Cuisson AU Gril VentiléeNiveau Cuisson AU GrilComment utiliser le programmateur électronique Signal SonoreDescription des symboles lumineux Réglage DE L’HEURERéglage MinuterieCuisson SEMI-AUTOMATIQUE Au cours de la cuissonCuisson Automatique Démarrage de la cuissonExemples DE Programmation DE LA Cuisson Automatique Nettoyage et entretien Installation ET Retrait DE LA Grille DU Four Retrait DE LA Porte DU FourPièces DE Rechange AvertissementInstructions DE Mise À LA Terre Exigences électriquesInstallation à l’armoire Renseignements Généraux11/64 po 30 mm Raccordement électrique Raccordement Avec FIL DE Cuivre SeulementL1 N Page Page US CA
Related manuals
Manual 56 pages 4.04 Kb