R
BEFORE YOU START - DOUBLE & SINGLE MODELS
PARTS SUPPLIED
DOUBLE MODELS
Flexible Extrusion | Flexible Extrusion | Installation Tabs (2) | ||
for Sides (2) | for Top (1) | |||
Edge Protector (1) | Clamp |
|
| |
(1) | Washer | Phillips 16mm | ||
| ||||
|
| |||
|
| (1) | Screws (7) | |
|
|
| Moisture | |
Drain Hose | Drain Hose | Wire | Protection | |
Tape (1) | ||||
Support (1) | Joiner (1) | Clips (2) | ||
p/n 527208 |
SINGLE MODELS
Wire | Edge |
Clip (1) | |
| Protector (1) |
Drain Hose
Support (1)
Drain Hose | |
Joiner (1) | |
Flexible Extrusion for Sides (2) | Clamp (1) |
|
Phillips 16mm Screws (5)
Moisture Protection Tape (1) p/n 527208
Washer (1)
Prefinished
Toe Kick (1)
White prefinished toe kick kit p/n 526678 or Black prefinished toe kick kit p/n 526679
or Iridium prefinished toe kick kit p/n 527109
TOOLS NEEDED
Wooden Chopping Board | Drill & No.2 Phillips Bit |
Tape Measure | No.2 Phillips Screwdriver |
Spirit Level | Flat Screwdriver |
Safety Glasses | Adjustable Wrench or M5 Socket |
Utility Knife | Ø11/2” (38mm) Hole Saw |
Pencil | Side Cutting Pliers |
Sandpaper |
|
SPARE PARTS INSTALLATION KIT FOR SINGLE & DOUBLE MODELS: p/n 526676
INSTALLATION PREPARATION
ELECTRICAL PREPARATION
A)The switched power outlet must be outside the DishDrawer® cavity so that it is accessible after installation.
B)The switched power outlet must be between 6” (150mm) and 18” (450mm) from the DishDrawer® cavity.
C)Refer to Page 9, Step 5 for electrical connection options.
Important!
The services hole in the DishDrawer® cavity needs to be large enough for the plug on the power supply cord to fit through, but MUST NOT be more than 11/2” (38mm).
PLUMBING & DRAINAGE PREPARATION
A)A readily accessible valve must be installed in the water supply pipe.
B)If the supply pressure exceeds 145 psi (1000kPa), then a pressure limiting valve must be used.
C)Review Plumbing Options on pages 4 or 6. Choose a method that best suits your needs.
D)A Drain Hose extension Kit P/N 525798 will extend the drain hoses by 1413/4” (3.6m). The kit is available from the nearest Fisher&Paykel Authorized Service Agent. DO NOT extend beyond this limit.
E)This Dishwasher’s maximum drain height is 371/2” (950mm).
CAVITY PREPARATION
A)It is recommended that all cabinetry surrounding the DishDrawer® (including the underside of the countertop) is sealed with an oil based paint or
damage. The air in the cavity can get very hot and humid (saturated at 122oF/50oC)
B)The
C)Be sure the cavity provides sufficient material to secure the DishDrawer® using the mounting tabs (refer to step 1, page 7). If there is
nothing to screw to, add a brace. See page 3 or 5 for screw locations.
D)The services hole MUST be immediately adjacent to the rear lower corner of the cabinetry. If not, the hoses will prevent the DishDrawer® being pushed back into the cavity all the way. The hole can be located on either side depending on the location of the services.
E)Be sure the cavity sides are plumb (vertical) as this will assist with levelling the DishDrawer® .
F)Minimum clearances:
1/8” (2.5mm) |
1/8” (2.5mm) |
1/2” (13mm) |
ELECTRICAL INFORMATION
POWER SUPPLY CORD
A)Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord.
B)If the power supply cord is damaged, it must be replaced by
the Manufacturer, Service Agent or a similarly qualified person in order to avoid a hazard.
GROUNDING INSTRUCTIONS
A)This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.
WARNING!
Improper connection of the
B)This appliance is equipped with a power supply cord having an
WARNING!
Do not modify the power supply plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adaptor plug or multiple outlet box.
2