GE 26, 25, 23 About the shelves and bins, Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Page 10

Instructions

About the shelves and bins.

Not all features are on all models.

Snugger

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Operating Instructions Safety

Refrigerator bin

Freezer tilt-out bin

Bins

The larger refrigerator door bins and freezer tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight up, then lift up and out.

To replace or relocate: Engage the back side of the bin in the molded supports on the door. Then push down on the front of the bin.

Bin will lock in place.

The snugger helps prevent tipping, spilling or sliding of small items stored on the door shelf. Place a finger on either side of the snugger near the rear and move it back and forth

to fit your needs.

Top Freezer Bins

Do not block

Top freezer bin

Do not block

CAUTION:

Be careful when placing items in the top bin. Make sure that items do not block or fall into the ice chute.

CAUTION: Part must be in place as shown for proper ice dispensing. Food cannot be stored in this location.

Top freezer bin (on some models)

Press tab and pull shelf forward to remove

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to reach items stored behind others. The special edges are designed to help prevent spills from dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop, then press down on the tab and slide the shelf straight out.

To replace or relocate:

Line the shelf up with the supports and slide it into place. The shelf can be repositioned when the door is at 90° or more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide shelf down to the desired position, line up with the supports and slide into place.

Make sure you push the shelves all the way back in before you close the door.

Consumer Support Troubleshooting Tips

QuickSpace™ Shelf

This shelf splits in half and slides under itself for storage of tall items on the shelf below.

This shelf can be removed and replaced or relocated just like Slide-Out Spillproof Shelves.

On some models, this shelf cannot be used in the lowest position.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Ge.com Write the model and serial numbers here Model # Serial #Safety Precautions Safety InstructionsRefrigerator or Freezer RefrigerantsBefore You Throw Away Your Old Ge.comHOW to Connect Electricity Operating InstructionsInstructions About the temperature controlsInstructions Installation SupportInstallation Instructions Tips About Set FeaturesSafety Instructions About TurboCoolHow to Use How to Remove and Replace the DrawerAbout CustomCool.on some models CustomCool ChartHow to Use the Beverage Center LCD models only Consumer SupportAbout QuickFreeze.on some models About the water filterSlide-Out Spillproof Shelf About the shelves and binsRefrigerator Door Bins and Freezer Door Tilt-Out Bins QuickSpace ShelfSlide-Out Freezer Shelves Tips Consumer SupportFreezer Baskets Fixed Freezer ShelvesAbout the refrigerator doors Operating Instructions Safety InstructionsInstallation Instructions Refrigerator DoorsAbout the crispers and pans Safety Instructions Operating InstructionsAbout crisper removal Automatic Icemaker Operating Instructions SafetyAbout the automatic icemaker Special note about dispenser modelsAbout the ice and water dispenser. on some models Cleaning the Outside Care and cleaning of the refrigeratorInstallation Instructions Troubleshooting Tips Cleaning the InsidePreparing for Vacation SafetyBehind the Refrigerator Preparing to MoveReplacing the light bulbs Operating InstructionsPanels less than 1/4 ″ 6 mm thick Trim kits and decorator panels″ 19 mm or Raised Panel 25‘ CustomStyle Dimensions for Custom Wood Panels Installation Instructions23‘ Dimensions for Custom Wood Panels Freezer Panel Without DispenserInsert the Bottom Freezer Panel on dispenser models Inserting the door panelsInsert the Freezer Panel and Fresh Food Panel Attach the Top Trim on the Freezer and Fresh Food DoorsInstall the Side Trim These pieces are tucked inside the refrigerator door handleBefore YOU Begin Preparation Water Supply to the IcemakerMoving the Refrigerator Remove the Base GrilleDisconnect the Power Coupling on some models Remove the Freezer DoorRemove the Freezer Door Remove the Refrigerator DoorReplacing the Doors Lift the refrigerator door up and off the bottom hingeRefrigerator Location Dimensions and SpecificationsClearances Turn on the Water Supply Plug in the RefrigeratorLevel the Refrigerator PUT the Refrigerator in PlaceLevel the Doors SET the Controls Replace the Base GrilleStart the Icemaker What YOU will Need Choose the Valve Location Shut OFF the Main Water SupplyDrill the Hole for the Valve Route the Tubing Fasten the Shutoff ValveTighten the Pipe Clamp Connect the Tubing to the ValveTroubleshooting Tips Consumer Support Safety Instructions Operating Instructions InstallationNormal operating sounds Refrigerator does not operate Before you call for service…Consumer Support Troubleshooting Tips Slight vibration is normalSetting. This is normal Is warm Is first installed Water dispenser has not beenLast setting was Crushed ConnectedOperating Instructions Safety Instructions Installation Evaporator, condenser What is covered How Long Warranted Parts LabourCompressor Tubing and refrigerantGE Will Replace Operating Instructions Safety InstructionsWhat GE Will Not Cover General Installation/Operation/Maintenance Requirements Performance Data SheetOperating Specifications Special NoticesName Address City State Zip Signature Date We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Safety Instructions Operating Instructions
Related manuals
Manual 112 pages 21.67 Kb Manual 88 pages 38.63 Kb Manual 100 pages 44.66 Kb

23, 26, 25 specifications

The GE 25, officially known as the General Electric 25 (GE 25), is a revolutionary advanced gas turbine designed to enhance the efficiency and productivity of power generation. This cutting-edge turbine is engineered with an eye towards meeting the evolving demands of the energy market while ensuring environmental sustainability.

One of the primary features of the GE 25 is its highly efficient combustion process. Utilizing advanced combustion technology, the turbine achieves lower emissions of nitrogen oxides (NOx) while maintaining a high power output. The GE 25 is designed for use in both simple cycle and combined cycle power plants, making it a versatile choice for various energy generation applications. The turbine's ability to transition seamlessly between these cycles allows operators to optimize energy production based on demand.

The GE 25 is built with advanced materials that enhance durability and performance. The components are constructed from high-temperature alloys that withstand extreme operating conditions, thus ensuring longevity and lower maintenance costs. This durability is crucial as it minimizes downtime and maximizes productivity in power generation facilities.

Innovative technologies incorporated into the GE 25 include advanced aerodynamics and an intelligent control system. The turbine features an optimized blade design that improves airflow efficiency and reduces drag, resulting in higher overall performance. Additionally, the intelligent control system offers real-time monitoring and analysis, enabling predictive maintenance and ensuring that the turbine operates at peak efficiency.

The turbine's modular design simplifies installation and maintenance processes. This allows for faster commissioning times and enhances operational flexibility, making it a preferred choice for both new installations and retrofitting older plants. The GE 25 is also compatible with a wide range of fuel types, including natural gas, biogas, and even hydrogen blends, which aligns with the industry's shift towards more sustainable energy sources.

In summary, the GE 25 stands out as a powerhouse in the gas turbine industry, with its cutting-edge features, advanced technologies, and robust characteristics. By prioritizing efficiency, durability, and flexibility, the GE 25 meets the current and future energy needs while contributing to a greener planet. As the demand for reliable and sustainable energy sources continues to grow, the GE 25 will play a vital role in shaping the future of power generation.
Top Page Image Contents