GE 26, 25, 23 Disconnect the Power Coupling on some models, Remove the Freezer Door

Page 25

Installation Instructions

4DISCONNECT THE POWER COUPLING (on some models)

If the refrigerator has a water dispenser, there is a power line (harness) from the cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect, pull apart at the coupling.

Bottom freezer hinge

5DISCONNECT THE ELECTRICAL CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors (harnesses) from the cabinet into the bottom hinge

on the refrigerator door that must be disconnected.

To disconnect, pull apart each connector.

Bottom refrigerator hinge

6CLOSE THE FREEZER AND REFRIGERATOR DOORS

7REMOVE THE FREEZER DOOR

ARemove the freezer door top hinge cover

(if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

BRemove the two 5/16″ or 1/8″ hex head screws, then lift the hinge straight up to free the hinge pin.

5/16″ or 1/8″ hex head

COpen the freezer door to 90.°

90°

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Write the model and serial numbers here Model # Serial # Ge.comSafety Instructions Safety PrecautionsBefore You Throw Away Your Old RefrigerantsRefrigerator or Freezer Ge.comOperating Instructions HOW to Connect ElectricityInstructions Installation About the temperature controlsInstructions SupportSafety Instructions About Set FeaturesInstallation Instructions Tips About TurboCoolHow to Remove and Replace the Drawer How to UseHow to Use the Beverage Center LCD models only CustomCool ChartAbout CustomCool.on some models Consumer SupportAbout the water filter About QuickFreeze.on some modelsRefrigerator Door Bins and Freezer Door Tilt-Out Bins About the shelves and binsSlide-Out Spillproof Shelf QuickSpace ShelfFreezer Baskets Tips Consumer SupportSlide-Out Freezer Shelves Fixed Freezer ShelvesInstallation Instructions Operating Instructions Safety InstructionsAbout the refrigerator doors Refrigerator DoorsAbout the crispers and pans Safety Instructions Operating InstructionsAbout crisper removal About the automatic icemaker Operating Instructions SafetyAutomatic Icemaker Special note about dispenser modelsAbout the ice and water dispenser. on some models Installation Instructions Troubleshooting Tips Care and cleaning of the refrigeratorCleaning the Outside Cleaning the InsideBehind the Refrigerator SafetyPreparing for Vacation Preparing to MoveOperating Instructions Replacing the light bulbsPanels less than 1/4 ″ 6 mm thick Trim kits and decorator panels″ 19 mm or Raised Panel 23‘ Dimensions for Custom Wood Panels Installation Instructions25‘ CustomStyle Dimensions for Custom Wood Panels Freezer Panel Without DispenserInsert the Freezer Panel and Fresh Food Panel Inserting the door panelsInsert the Bottom Freezer Panel on dispenser models Attach the Top Trim on the Freezer and Fresh Food DoorsThese pieces are tucked inside the refrigerator door handle Install the Side TrimPreparation Water Supply to the Icemaker Before YOU BeginRemove the Base Grille Moving the RefrigeratorRemove the Freezer Door Disconnect the Power Coupling on some modelsRemove the Refrigerator Door Remove the Freezer DoorLift the refrigerator door up and off the bottom hinge Replacing the DoorsRefrigerator Location Dimensions and SpecificationsClearances Plug in the Refrigerator Turn on the Water SupplyLevel the Refrigerator PUT the Refrigerator in PlaceLevel the Doors SET the Controls Replace the Base GrilleStart the Icemaker What YOU will Need Choose the Valve Location Shut OFF the Main Water SupplyDrill the Hole for the Valve Tighten the Pipe Clamp Fasten the Shutoff ValveRoute the Tubing Connect the Tubing to the ValveTroubleshooting Tips Consumer Support Safety Instructions Operating Instructions InstallationNormal operating sounds Consumer Support Troubleshooting Tips Before you call for service…Refrigerator does not operate Slight vibration is normalLast setting was Crushed Is warm Is first installed Water dispenser has not beenSetting. This is normal ConnectedOperating Instructions Safety Instructions Installation Compressor What is covered How Long Warranted Parts LabourEvaporator, condenser Tubing and refrigerantGE Will Replace Operating Instructions Safety InstructionsWhat GE Will Not Cover Operating Specifications Performance Data SheetGeneral Installation/Operation/Maintenance Requirements Special NoticesName Address City State Zip Signature Date We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Safety Instructions Operating Instructions
Related manuals
Manual 112 pages 21.67 Kb Manual 88 pages 38.63 Kb Manual 100 pages 44.66 Kb

23, 26, 25 specifications

The GE 25, officially known as the General Electric 25 (GE 25), is a revolutionary advanced gas turbine designed to enhance the efficiency and productivity of power generation. This cutting-edge turbine is engineered with an eye towards meeting the evolving demands of the energy market while ensuring environmental sustainability.

One of the primary features of the GE 25 is its highly efficient combustion process. Utilizing advanced combustion technology, the turbine achieves lower emissions of nitrogen oxides (NOx) while maintaining a high power output. The GE 25 is designed for use in both simple cycle and combined cycle power plants, making it a versatile choice for various energy generation applications. The turbine's ability to transition seamlessly between these cycles allows operators to optimize energy production based on demand.

The GE 25 is built with advanced materials that enhance durability and performance. The components are constructed from high-temperature alloys that withstand extreme operating conditions, thus ensuring longevity and lower maintenance costs. This durability is crucial as it minimizes downtime and maximizes productivity in power generation facilities.

Innovative technologies incorporated into the GE 25 include advanced aerodynamics and an intelligent control system. The turbine features an optimized blade design that improves airflow efficiency and reduces drag, resulting in higher overall performance. Additionally, the intelligent control system offers real-time monitoring and analysis, enabling predictive maintenance and ensuring that the turbine operates at peak efficiency.

The turbine's modular design simplifies installation and maintenance processes. This allows for faster commissioning times and enhances operational flexibility, making it a preferred choice for both new installations and retrofitting older plants. The GE 25 is also compatible with a wide range of fuel types, including natural gas, biogas, and even hydrogen blends, which aligns with the industry's shift towards more sustainable energy sources.

In summary, the GE 25 stands out as a powerhouse in the gas turbine industry, with its cutting-edge features, advanced technologies, and robust characteristics. By prioritizing efficiency, durability, and flexibility, the GE 25 meets the current and future energy needs while contributing to a greener planet. As the demand for reliable and sustainable energy sources continues to grow, the GE 25 will play a vital role in shaping the future of power generation.
Top Page Image Contents