Defrosting on push button defrost models only

ge.com

Defrosting (on push button defrost models only)

Defrost whenever frost on the wall of the ice tray compartment becomes 1/4″ thick.

To defrost:

■ Remove foods and ice trays from the refrigerator and ice tray compartment.

■ Ensure drip tray is below ice tray compartment to collect water.

Defrost push

button■ Push in the red “Defrost Button” located in the center of the temperature control dial. Defrost cycle will start immediately.

NOTE: Turning the temperature control dial to the OFF position is not required.

Defrosting usually takes a few hours. When defrosting is complete, the red “Defrost Button” will release automatically. Then the refrigerator will resume normal operation while moving towards the set temperature. NOTE: After defrosting, allow a few hours to reach the set temperature before making any further adjustments.

To defrost faster, keep the door open. Also, pouring warm (not hot) water on the frosted part may speed defrosting. Do not use boiling water—it may damage plastic parts.

CAUTION: If you decide to “speed up” the defrost cycle by manually removing ice, NEVER use a sharp or metallic instrument to chip away the ice as it may damage the cooling coils. (A punctured cooling coil will cause serious problems and void the warranty.) Do no use any electrical device in defrosting your refrigerator.

After defrosting:

■After red “Defrost Button” has released, empty water from the drip tray. Wash the tray with warm water. Dry the drip tray completely.

■Wipe the ice tray compartment with a damp cloth.

■Return drip tray to below ice tray compartment.

■Return food and ice trays to the refrigerator and close the door.

	IMPORTANT: If the red “Defrost Button” is pushed accidentally,
	it can not be manually released. The defrost cycle will run until
	complete. To speed up the defrost cycle, remove the drip tray and
	apply a warm damp cloth against the temperature sensing wire
	located on the underside of the ice tray compartment. After several
Temperature	minutes, the heat from the warm cloth will raise the temperature of
sensing wire	the thermostat, causing the defrost cycle to end and releasing the
	red “Defrost Button.” The refrigerator will then resume normal
	operation.
	NOTE: If ice buildup is very thick, it may keep the ice tray compartment door
	from opening or closing completely. Don’t try to force it open or closed; after
	defrosting, the door will open and close easily.

Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support

162D9639P009 specifications

The GE 162D9639P009 is an advanced component widely recognized for its application in various industrial and commercial systems. This part, often associated with General Electric (GE), represents cutting-edge technology designed for enhancement in performance, reliability, and efficiency.

One of the standout features of the GE 162D9639P009 is its robust construction, allowing it to endure rigorous operational environments. This durability is critical in industrial applications, where components face continuous use, varying temperatures, and potentially harmful conditions. The materials used in the construction of this part are selected for high strength and resistance to wear, ensuring long lifespan and reducing the need for frequent replacements.

In terms of technological capabilities, the GE 162D9639P009 integrates advanced electronic functionality, which enhances its operational efficiencies. With innovative circuitry designed to minimize power consumption, this component supports sustainability initiatives by providing energy-efficient solutions. The electronics not only improve the performance metrics of the systems in which they are integrated but also help in managing operational costs over time.

Another notable characteristic of the GE 162D9639P009 is its compatibility with a wide range of systems, making it a versatile choice for various applications. This adaptability opens doors to many industrial sectors, from manufacturing and construction to energy production and transportation. The ease of installation and integration of this component allows for quick deployments and upgrades in existing systems, minimizing downtime and promoting continuity of operations.

Furthermore, the GE 162D9639P009 is designed with user-friendly features that simplify maintenance and monitoring. Built-in diagnostics and indicators enable operators to quickly assess functionality and performance, ensuring timely interventions when necessary. This proactive maintenance capability enhances overall system performance and reliability, which is essential in high-stakes environments.

In conclusion, the GE 162D9639P009 stands as a testament to General Electric's commitment to innovation and excellence in engineering. With its robust design, advanced technology, wide compatibility, and user-centric features, this component is instrumental in driving efficiency and reliability across various applications, solidifying its role as a critical part of modern industrial solutions.