Alto-Shaam 714, VHes-10, VHes-5, 1220, 610, 1010, 2020, 1018 manual Combitouch checklist, Clearances

Page 31

installation

combitouch® checklist

Use this list as a final check of oven installation conformance.

Damage directly attributed to improper set up, installation, or cleaning can invalidate warranty claims.

CLEARANCES:

Left:

6" (152mm) — Service access of 18" (457mm) recommended.

 

20" (508mm) from heat producing equipment.

Right:

4" (102mm)

Back:

4" (102mm) for plumbing

Top:

20" (508mm) for air movement

are all CLEARANCE

 

 

requirements met?

YES

NO

if no, explain:________________________

________________________________________

water supply and drains:

Verify hook-up to two (2) separate cold water supply lines with a 3/4" (19mm) water connection supply line. Verify inlet water pressure is at a minimum of 30 PSI (2.8 bar). Maximum water pressure is not to exceed 90 PSI (6 bar). Verify drain diameter of 1-1/2" (41mm) with a positive descending slope, and with a 2" (51mm) air gap which is free of obstructions before connection to the site drain. Verify 1/8" (3.2mm) pitch to 10' (305cm) of drain line.

important: Alto-Shaam has listed Water Quality Requirements in the installation manual for this equipment. It is the responsibility of the end user to have the water connected to this appliance tested to ensure these standards are met before putting the oven into use. Failure to meet these standards will void the warranty if damage to the oven is found to be related to water quality.

are both water supply lines

properly connected?

YES

NO

if no, explain:___________________________

is a filter system installed

 

on this unit?

YES

NO

store has seen this

 

 

recommendation:

YES

NO

Signature of Store Representative:

___________________________________________

ELECTRICAL CONNECTIONS:

Verify electrical power requirements for oven. Verify voltage at terminal block.

Check all terminals for tightness.

VOLTAGE: ______________

PHASE: ______________

LINE VOLTAGE AT TERMINAL BLOCK (to ground):

ÂLINE 1: _________ LINE 2:_________ LINE 3: _________

LINE VOLTAGE (phase to phase): LINE 1 to 2: __________

LINE 2 to 3: __________

LINE 3 to 1: __________

ELECTRICAL SUPPLY LINE SIZE: ______________

breaker size: ______________

ALL ELECTRICAL TERMINALS TIGHT:

YES

NO

 

 

 

 

 

control board connections & operation:

ALL BOARD CONNECTIONS TIGHT:

YES

NO

 

With the Power on, press the Set-Up Key to access software version, and record.

YES

NO

 

ALL FUNCTIONS ARE DISPLAYED:

SOFTWARE VERSION:

ALL FUNCTIONS on control OPERATE:

YES

NO

unit OPERATEs in all modes:

YES

NO

RB_____________ DB_____________

if no, explain:_________________________________________

 

 

 

PHYSICAL CONDITION: *r e f e r e n c e i n s t a l l a t i o n i n s t r u c t i o n s f o r c o m p l e t e i n f o r m a t i o n

 

4

Bottom of oven has been checked for damage due to improper positioning on site

 

Verify all gaskets, hoses, and carts* are in place and function properly......................................................................

If oven includes a cart, verify proper installation of the rack guide on companion warmer or chiller*.....................

Verify the installation of drip pans*, racks, shelves, drain screen, spray hose* ..........................................................

Verify the oven is level and installed on a solid, water resistant floor.........................................................................

service agency:

model no.:

tech signature:

start-up date:

installation name:

serial no.:

customer signature:

Combitouch® ES series • electric INSTALLATION MANUAL • 29..

Image 31
Contents ES electric Installation P a c k i n g L i v e r yN g e r Safety procedures and precautionsInstallation codes & Standards Site InstallationVentilation requirements Minimum Clearance Requirements Positioning on siteLifting Instructions Positioning requirements 610, 714, 1018 CombiGuard Common specifications610ES Touch 610es610ES 610ESi Touch 610esi610ESi 610ESiN Touch 610esiN610ESiN 1010ES Touch 1010es1010ES 1010ESi Touch 1010esi1010ESi 33 837mm 1010esiN714ES Touch 714es714ES 714ESi 714ESi Touch1018ES Touch 1018es1018ES 1018ESi Touch 1018esi1018ESi 1220ES Touch 1220es1220ES 1220ESi Touch 1220esi1220ESi 2020ES Touch 2020es2020ES 2020ESi Touch 2020esi2020ESi Electrical connection Hard wired modelsTerminal Block Ground Electrical Connection Risk of electric shock Mobile equipment restraintWater quality requirement Water requirements Two 2 cold water inlets drinking quality Water connectionsWater drainage Water ValveOn/O Clearances Combitouch checklistPress the Start Icon to Acknowledge the Error Error codesE15 E51 E93 Combitouch motor control error codes Press the Start Icon to Acknowledge the Error Condensate drain Ventless hood optionOperation Ventless Hood Power KnobOriginal equipment limited warranty TRansportation damage and claims
Related manuals
Manual 39 pages 38.94 Kb Manual 36 pages 33.23 Kb

1018, 2020, 1010, COMBITHERM COMBINATION Oven / Steamer ES electric combitouch, 714 specifications

Alto-Shaam is known for its innovative cooking and holding equipment designed for the foodservice industry, and their VHes product line is no exception. This range includes models VHes-10, VHes-5, 1220, 610, and 714, each built with unique features and advanced technologies to meet the demands of modern kitchens.

The VHes-10 and VHes-5 models are equipped with Alto-Shaam’s exclusive Halo Heat technology, which provides precise temperature control and ensures even heat distribution. This technology gently holds food at the perfect serving temperature without drying it out, enhancing both flavor and texture. These models also feature Energy Star certification, reflecting their energy-efficient design, which helps kitchens reduce operational costs while supporting sustainability goals.

The VHes-10 boasts a larger capacity, capable of accommodating more food items, while the VHes-5 is designed for smaller operations or limited spaces, providing versatility in the kitchen. Both models come with digital control panels for easy temperature adjustments and monitoring, ensuring that chefs can maintain optimal conditions at all times.

Moving on to the 1220, 610, and 714 models, these units cater to diverse holding needs within foodservice operations. Each model is designed to be user-friendly, with clear digital displays and intuitive controls that allow chefs to quickly set and adjust holding temperatures. The 1220 model is particularly popular for its spacious design, which supports larger quantities of food, making it ideal for bustling kitchens and catered events.

The 610 and 714 models are engineered for flexibility, allowing operators to effectively manage their food items in various settings. Their compact sizes combined with smart technology make them an excellent choice for both front-line service environments and back-of-house operations. Notably, all these models support multiple food types, enabling establishments to hold everything from vegetables to protein dishes without compromising quality.

In summary, Alto-Shaam’s VHes series, including the VHes-10, VHes-5, 1220, 610, and 714, integrates cutting-edge technologies such as Halo Heat and efficient designs into versatile equipment. With an emphasis on energy savings, precise temperature control, and user convenience, these models are vital for any foodservice operation seeking to elevate their food holding and serving capabilities.