Cómo usar la Herramienta | Campbell Hausfeld SN318K00 guide

150 PSI WP

3/8” I.D.

internal parts

60 psi Min.

100 psi Max.

GireRotate

Operating Instructions

Model SN318K00

Manual de Instrucciones

Modelo SN318K00

Operating The Tool

(Continued)

3. After adding oil, run tool briefly. Wipe off any excess oil from the cap exhaust.

RECOMMENDED HOOKUP

The illustration below shows the recommended hookup for the tool.

work surface followed by pulling the trigger.

The trigger must be released to reset the tool before another fastener can be driven.

OPERATING A SEQUENTIAL TRIP NAILER

Check the operation of the Work Contact Element (WCE) trip mechanism before

position. The tool MUST NOT OPERATE. Do not use the tool if it operates while lifted from the work surface. Personal injury may result.

7.Pull the trig- ger and

depress the work contact

element

(WCE) against the work surface. The tool MUST NOT OPERATE.

8. Depress the

Cómo usar la Herramienta (Cont.)

COMO CHEQUEAR EL ELEMENTO DE CONTACTO

Chequée el fun-

cionamiento del mecanismo del ele- mento de contacto antes de cada uso. El elemento de contacto se debe desplazar libremente, sin pegarse, a lo largo del área de desplazamiento. El resorte del elemento de contacto debe

7. Apriete el

gatillo y pre- sione el

Elemento de

Contacto de Trabajo contra la super- ficie de trabajo. La herramienta

DEBE OPERAR.

PARA CARGAR Y DESCARGAR LA HERRAMIENTA

1.Siempre conecte la herramienta a la fuente de suminsitro de aire antes de colocarle los sujetadores.

6,90 bar ya que ésto reduciría la durabilidad de la herramienta.

PARA AJUSTAR LA DIRECCION DEL TUBO DE ESCAPE

La herramienta

está equipado con un deflector ajustable de la dirección del tubo de escape. Éste le

permite al usuario cambiar la dirección del tubo de escape. Simplemente mueva

1. The air com- pressor must be able to maintain a minimum of 60 psi when

each use. The WCE must move freely without binding through its entire trav- el distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the tool if the WCE trip mechanism is not operating properly. Personal injury may occur.

Work Contact

Element
(WCE) against	2
1	2
the work sur-

face. Pull the trigger. The tool

MUST OPERATE.

regresar el elemento de contacto a su posición original totalmente extendido. No use la herramienta si el mecanismo del elemento de contacto no está fun- cionando adecudamente. Podría oca- sionarle heridas.

1. Desconecte la herramienta de

2.Empuje hacia abajo sobre el boton del seguro. Mueva la tapa del cargador hacia atrás.

Botón del

seguro

el deflector hacia la dirección deseada.

QUÉ HACER CUANDO LA HERRA- MIENTA TENGA UN SUJETADOR ATASCADO

1. Desconecte la herramienta de

the tool is being used. An inade- quate air supply can cause a loss of power and inconsistent driving.

1.Disconnect the air supply from

the tool.

improperly functioning tool must not be used. Do not actuate the tool unless

la fuente de su- ministro de aire.

3.Para grapas, cargue una tira de gra- pas con las coronas montadas sobre el riel del cargador.

la fuente de suministro de aire.

2. An oiler can be used to provide oil circula- tion through the tool. A filter can be used to remove liquid and solid impurities which can rust or “gum up” of the tool.

3. Use 3/8” air hoses with a minimum working pres- sure of 150

psi. Use 1/2” air hoses for 50’ run or longer. For better performance, install a 3/8” quick plug (1/4” NPT threads) with an inside diameter of

.315" (8mm) on the tool and a 3/8” quick coupler on the air hose.

2.Remove all fas- teners from the

magazine (see Loading/ Unloading).

	3. Make sure the trig-
	ger and work con-
	tact element (WCE)
	move freely up and	movement
	down without stick-	movement
	down without stick-
	ing or binding.

4.Reconnect air supply to the tool.

the tool is placed firmly against the work piece.

CHECKING THE WORK CONTACT ELEMENT (WCE)

Check the operation of the Work Contact Element (WCE) trip mechanism before each use. The WCE must move freely without bind- ing through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the tool if the WCE trip mechanism is not operating properly. Personal injury may occur.

1. Disconnect the air supply from the tool.

2. Saque todos los sujetadores del cargador (Vea la Sección Carga- Descarga)

3.Cerciórese de que el gatillo y el ele- mento de contacto

	se muevan libre-	movemiento
	mente en ambos	movemiento
	mente en ambos
	sentidos sin atascarse o pegarse.
4.	Reconecte la
	herramienta a la
	fuente de sumi-
	nistro de aire.
5.	Presione el
	Elemento de
	Contacto de Trabajo

Carril del cargador

4.	Empuje la tapa
	del cargador
	hacia delante
	hasta que el
	botón del
	seguro salte hacia arriba.

5. Siempre descargue el sujetador

antes de remover la herramienta de

servicio. La descarga se hace

siguiendo el proceso inverso de la

carga; sin embargo, siempre se

tiene que desconectar la manguera

2. Remueva

todos los suje- tadores del

depósito (vea Para Cargar

/Descargar la Herramienta). De lo contrario, hará que los sujetadores se expulsen desde la parte delantera de la

herramienta cuando se remueve el conjunto de la boca.

3. Remueva (3)

tornillos de

cabeza de la

boca de la her-

ramienta.

Remueva la placa de la boca, el

espaciador y el Elemento de

Contacto de Trabajo para dejar

expuesto el sujetador atascado.

4. Use a pressure

regulator on the compressor, with

an operating pressure of 0 -125

psi. A pressure regulator is required to control the operating pressure of the tool between 60 and 100 psi.

SINGLE SEQUENTIAL MODE

This mode

requires the trig-

ger to be pulled each time a fas-

tener is driven. The tool can be actuat- ed by depressing the WCE against the

5.Depress the Work Contact Element (WCE) against the work surface with- out pulling the trig- ger. The tool MUST

NOT OPERATE. Do not use the tool if it operates without pulling the trigger. Personal injury may result.

6.Remove the tool from the work sur-

face. The Work Contact Element (WCE) must return to its original down

2. Remove all fas-

teners from

the magazine.

(See "Loading/

Unloading the Tool" section.)

3.Make sure the trigger and Work Contact Element

(WCE) move freely up and down with-

out sticking or bind-	movement
ing.

4. Reconnect air supply to the tool.

contra la superficie

de trabajo sin apre-

tar el gatillo. La herramienta NO

DEBE OPERAR. No use la herra-

mienta si opera sin apretar el gatillo.

Se pueden producir lesiones person-

ales.

6. Remueva la her-

ramienta de la super-

ficie de trabajo. El

Elemento de

Contacto de Trabajo

tiene que volver a su posición origi-

nal. La herramienta NO DEBE

OPERAR. No use la herramienta si

opera mientras está levantada de la

superficie de trabajo.

de aire antes de descargarla.

PARA AJUSTAR LA PENETRACION DE LOS SUJETADORES

1.Regule la pre- sión de aire en la herramienta a 3,45 bar.

2.Conecte las mangueras de aire y pruebe la penetración clavando unos sujetadores en un pedazo de madera. Si éstos no penetran hasta el nivel deseado, aumente la pre- sión de aire y pruebe una vez más, continúe haciéndolo hasta lograr los resultados deseados. La presión de la herramienta no debe exceder

4.	Vuelva a instalar el conjunto de la
	boca en el orden inverso del paso Nº3.
5.	Asegúrese que el
	gatillo funciona y

que el Elemento de

Contacto demovemiento Trabajo se mueve

libremente hacia arriba y hacia abajo sin atascarse o pegarse.

www.chpower.com

21 Sp

SN318K00 specifications

The Campbell Hausfeld SN318K00 is a versatile and robust air compressor designed to meet the needs of both professional and DIY users. This particular model stands out due to its powerful performance, portability, and user-friendly features, making it ideal for tasks ranging from inflating tires to powering pneumatic tools.

One of the main features of the SN318K00 is its 3-gallon tank, which offers an optimal balance between capacity and portability. Weighing in at a manageable 37 pounds, this compact air compressor can easily be transported to various job sites or stored without taking up much space. The oil-free pump technology enhances its convenience, eliminating the need for oil changes and reducing maintenance requirements, allowing for hassle-free operation.

This compressor is equipped with a 1.0 HP motor that delivers a maximum pressure of 100 PSI, ensuring sufficient power for a wide range of applications. Its quick recovery time allows users to maintain a continuous airflow, which is particularly beneficial when using multiple tools or for extended periods. The noise level is also considerate, operating at a sound level of approximately 68 dBA, which is relatively quiet for an air compressor, making it suitable for indoor use.

Another noteworthy feature is the integrated control panel that includes an easy-to-read pressure gauge and a quick-release valve for effortless pressure adjustments. The SN318K00 also comes with a 25-foot air hose and various accessories, including a tire inflator, blow gun, and nozzles, providing users with everything they need to get started right out of the box.

Designed for versatility, the Campbell Hausfeld SN318K00 can support a range of pneumatic tools, such as nailers, staplers, and impact wrenches. This makes it an excellent choice for home improvement projects, automotive repairs, and even light industrial applications.

Overall, the Campbell Hausfeld SN318K00 air compressor is a reliable and efficient solution for those seeking a compact yet powerful compressor. Its blend of features, technologies, and user-friendly design makes it an appealing option for anyone looking to enhance their toolkit, whether for professional tasks or personal projects. With its ease of use and versatility, the SN318K00 is an investment that can significantly boost productivity while maintaining user convenience.