Campbell Hausfeld SN318K00 Troubleshooting Guide, Componentes y Especificaciones de la Clavadora

Page 7
6,90 bar
O CO2

Manual de Instrucciones

Modelo SN318K00

Operating Instructions

Model SN318K00

Informaciones Generales de Seguridad

(Continuación)

Ésto le indica que hay una situación inmediata que LE OCASIONARIA la muerte o heridas de gravedad.

Lea y comprenda las eti- quetas y el manual de la herramienta. Si no respeta las advertencias, los ries- gos y las recomenda-

ciones, eso podría resultar en la MUERTE o en LESIONES GRAVES.

No use ningún tipo de

gas reactivo, incluyendo, pero no

limitado a, oxígeno y gases combustibles, como fuente de

energía. Use sólo aire comprimido filtrado, lubricado y regulado. El uso de un gas reactivo en vez de aire comprimido puede provocar que la herramienta explote, lo cual puede ocasionar la muerte o graves lesiones personales.

Use solamente una fuente de aire com-

primido de presión regulada para limitar la presión de aire suministrada a la her- ramienta. La presión regulada no debe exceder los 6,90 bar. Si el regu- lador falla, la presión transmitida a la herramienta no debe exceder los 13,79 bar. La herramienta puede

explotar, lo cual puede ocasionar la muerte o graves lesiones personales.

Nunca limpie la

herramienta con gasolina o ningún otro líquido inflam-

able. Nunca use la

herramienta en la cercanías de líqui- dos o gases inflamables. Una chispa podría encender los vapores y oca- sionar una explosión que podría oca- sionarle la muerte o heridas graves.

Siempre colóquese

en una posición firme y balanceada para usar o manip- ular la herramienta.

No quite, modifique ni haga de otro modo que el WCE (elemento de contac-

to de trabajo) o el gatillo dejen de fun- cionar. No haga fun-

cionar ninguna herramienta que haya sido modificada de manera sim- ilar. Eso puede resultar en muerte o graves lesiones personales.

No toque el gatillo

a menos que se estén clavando sujetadores. Nunca

conecte la línea de aire a la herramien- ta ni mueva la her-

ramienta cuando esté tocando el gatillo. La herramienta podría expul- sar un sujetador y producir la muerte o lesiones personales graves.

Ésto le

indica

que hay una situación que PODRÍA oca- sionarle la muerte o heridas graves.

Desconecte siempre la her- ramienta de la fuente de energía cuando no la esté aten-

diendo, cuando le esté realizando mantenimiento o reparaciones, des- obstruyéndola o moviéndola a un nuevo sitio. Siempre vuelva a conec- tar la tubería de aire ANTES de cargar los sujetadores. No cargue la herr- amienta con sujetadores cuando el gatillo esté oprimido o el WCE (ele- mento de contacto de trabajo) esté conectado. La herramienta puede expulsar un sujetador y producir la muerte o lesiones personales graves.

Siempre ajuste la herramienta con un conector o acoplador de mangueras colocado en o cerca de la her-

ramienta de un modo tal que se descargue todo el aire comprimido en la herramienta en el momento en que se desconecte el conector o acoplador. No use una válvula de chequeo o ninguna conexión que permita que el aire pemanezca en la herramienta. Se puede producir la muerte o lesiones personales graves.

Troubleshooting Guide

Stop using tool immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.

 

Problem

Cause

Solution

 

 

 

 

 

Air leaking at trigger valve

O-Rings in trigger valve housing are

Replace O-Rings. Check operation of Work Contact

 

 

damaged

Element (WCE)

 

 

 

 

 

Air leaking between hous-

Loose screws in housing

Tighten screws

 

ing and nose

Damaged O-Rings

Replace O-Rings

 

 

Damage to bumper

Replace bumper

 

 

 

 

 

Air leaking between hous-

Loose screws

Tighten screws

 

ing and cap

Damaged gasket

Replace gasket

 

 

 

 

 

Tool skips driving fastener

Worn bumper

Replace bumper

 

 

Dirt in nose piece

Clean drive channel

 

 

Dirt or damage prevent fasteners or

Clean magazine

 

 

pusher from moving freely in magazine

 

 

 

Damaged pusher spring

Replace spring

 

 

Inadequate air flow to tool

Check fitting, hose or compressor

 

 

Worn O-Ring on piston or lack of lubri-

Replace and lubricate O-Rings

 

 

cation

 

 

 

Damaged O-Ring on trigger valve

Replace O-Rings

 

 

Air leaks

Tighten screws and fittings

 

 

Cap gasket leaking

Replace gasket

 

 

 

 

 

Tool runs slow or has loss

Tool not lubricated sufficiently

Lubricate tool

 

of power

Broken spring in cylinder cap

Replace spring

 

 

Exhaust port in cap is blocked

Replace damaged internal parts

 

 

 

 

 

Fasteners are jammed in

Guide on driver is worn

Replace guide

Componentes y Especificaciones de la Clavadora

REQUIRE: 0,02 m3/min para clavar 10 sujetadores por minuto a 6,21 bar

ENTRADA DE AIRE: 6.4mm (1/4”)

NPT

RANGO DE LOS SUJETADORES: 1,27 cm a 3,18 cm (1/2” a 1 1/4”)

Orifico de salida de aire

 

 

Etiquetas de

 

advertencia

Código de

Botón del seguro

 

fecha

 

tool

Fasteners are not correct size

Use only recommended fasteners

 

Fasteners are bent

Replace with undamaged fasteners

 

Magazine or nose screws are loose

Tighten screws

 

Driver is damaged

Replace driver

CAPACIDAD DEL CARGADOR:

100 sujetadores por carga, calibre 18

GRAPAS: corona de 1/4”

PESO: 1,19 kg

LONGITUD: 24,1 cm (9 1/2”)

ALTURA: 19,1 cm (7 1/2”)

PRESION MÁXIMA: 6,90 bar

RANGO DE LA PRESIÓN: 4,14 bar - 6,90 bar

Elemento de contacto

de trabajo (WCE)

Gatillo

Cargador

Área de descarga de los sujetadores

www.chpower.com

18 Sp

7

 

Image 7
Contents Garantía Limitada Table of ContentsGeneral Safety Information DescriptionModel SN318K00 Tool Components And SpecificationsProblema Causa Solución Guía de Diagnóstico de AveríasOperating The Tool SujetadoresCómo usar la Herramienta Tool Repair Fastener And Replacement PartsAssembly Procedure For Seals Technical SupportConexión Recomendada FastenersStaples Interchange InformationCapacidad DEL Cargador Troubleshooting GuideProblem Cause Solution Componentes y Especificaciones de la ClavadoraInformaciones Generales de Seguridad Limited WarrantyÍndice DescripciónGarantie Limitée Table des MatièresGénéralités sur la Sécurité Modèle SN318K00Généralités sur la Sécurité Suite Guide de DépannageAttaches et Réparation de la Cloueuse Branchement RecommandéUtilisation de l’outil Attaches et Pièces de RechangeSupport Technique Utilisation de l’outil Suite

SN318K00 specifications

The Campbell Hausfeld SN318K00 is a versatile and robust air compressor designed to meet the needs of both professional and DIY users. This particular model stands out due to its powerful performance, portability, and user-friendly features, making it ideal for tasks ranging from inflating tires to powering pneumatic tools.

One of the main features of the SN318K00 is its 3-gallon tank, which offers an optimal balance between capacity and portability. Weighing in at a manageable 37 pounds, this compact air compressor can easily be transported to various job sites or stored without taking up much space. The oil-free pump technology enhances its convenience, eliminating the need for oil changes and reducing maintenance requirements, allowing for hassle-free operation.

This compressor is equipped with a 1.0 HP motor that delivers a maximum pressure of 100 PSI, ensuring sufficient power for a wide range of applications. Its quick recovery time allows users to maintain a continuous airflow, which is particularly beneficial when using multiple tools or for extended periods. The noise level is also considerate, operating at a sound level of approximately 68 dBA, which is relatively quiet for an air compressor, making it suitable for indoor use.

Another noteworthy feature is the integrated control panel that includes an easy-to-read pressure gauge and a quick-release valve for effortless pressure adjustments. The SN318K00 also comes with a 25-foot air hose and various accessories, including a tire inflator, blow gun, and nozzles, providing users with everything they need to get started right out of the box.

Designed for versatility, the Campbell Hausfeld SN318K00 can support a range of pneumatic tools, such as nailers, staplers, and impact wrenches. This makes it an excellent choice for home improvement projects, automotive repairs, and even light industrial applications.

Overall, the Campbell Hausfeld SN318K00 air compressor is a reliable and efficient solution for those seeking a compact yet powerful compressor. Its blend of features, technologies, and user-friendly design makes it an appealing option for anyone looking to enhance their toolkit, whether for professional tasks or personal projects. With its ease of use and versatility, the SN318K00 is an investment that can significantly boost productivity while maintaining user convenience.