End User Interface | 3D Connexion OL-6415-03 specs

Chapter 7 Configuring QoS on an Access Point

End User Interface

The 802.1Q user_priority maps to radio transmit priority queues automatically. VLAN default

user_priority value must be explicitly assigned through the command line interface (CLI), or the default value zero is used for the VLAN.

For voice traffic, whenever a 802.11 VOIP phone is associated with an access point, a default traffic egress filter with user_priority value 6 is installed for all the voice traffic.

Cisco Modular QoS CLI (MQC) uses a class-map clause to define traffic class and a policy-map clause to define QoS policy. A specific policy can be applied to an interface egress, ingress, or both.

If VLAN is not enabled, the MQC the policy-map should be applied to the interfaces. If VLAN is enabled, the policy-map should be applied to VLAN sub-interfaces. A policy-map applied to an interface is ignored.

Enable 802.11 Phone Support

Use the [no] dot11 phone command to configure the access point to advertise Symbol and QoS Basis Service Set (QBSS) information in the beacon and probe for response frames. The access point processes incoming Symbol frames and Cisco CDP Appliance-VLAN field to flag the client as a phone client.

Install IP Acess Control List

To control access to an interface, use the ip access-group command in interface configuration mode. To remove the specified access group, use the no form of this command.

[no] ip access-group <1-199> {in out}

Access lists are applied on either outbound or inbound interfaces. For standard inbound access lists, after receiving a packet, the Cisco IOS software checks the source address of the packet against the access list. For extended access lists, the router also checks the destination access list. If the access list permits the address, the software continues to process the packet. If the access list rejects the address, the software discards the packet and returns an ICMP host unreachable message.

Install MAC address Acess Control List

To assign an access list to a particular interface, use the bridge-group input-address-list command in interface configuration mode. This access list is used to filter packets received on that interface based on their MAC source addresses. To remove an access list from an interface, use the no form of this command.

bridge-group bridge-groupinput-address-list access-list-number

Install Ethernet Type or SAP Acess Control List

To filter Ethernet- and Subnetwork Access Protocol (SNAP)-encapsulated packets on input, use the bridge-groupinput-type-listcommand in interface configuration mode. To disable this capability, use the no form of this command.

bridge-groupbridge-group input-type-listaccess-list-number

Cisco Wireless Router and HWIC Configuration Guide

7-8	OL-6415-03

OL-6415-03 specifications

The 3Dconnexion OL-6415-03 is a highly advanced 3D mouse designed specifically for professionals in fields like architecture, engineering, product design, and animation. This device enhances productivity by offering intuitive control over 3D environments, making it an essential tool for those who work extensively with 3D modeling software.

One of the standout features of the OL-6415-03 is its unique six-degrees-of-freedom (6DoF) sensor. This technology enables users to control their models or scenes with a single hand, allowing for smooth, precise movements in all directions. The 3Dconnexion mouse allows users to navigate complex 3D spaces easily, enhancing the workflow and providing a more fluid experience when working with intricate designs.

The ergonomic design of the OL-6415-03 is another highlight. It is crafted for comfort during long working hours, reducing fatigue and strain. The mouse features a small footprint, making it suitable for limited desk space, while its premium materials ensure durability. The tactile surface provides a comfortable grip, allowing users to manipulate their designs with ease.

The device is also equipped with customizable buttons that enhance its versatility. Users can program these buttons to execute specific commands or shortcuts within their preferred software. This customization not only improves efficiency but also allows for a more personalized experience, catering to individual workflow needs.

The OL-6415-03 is compatible with a wide range of CAD applications, including popular software like SolidWorks, Autodesk Inventor, and SketchUp. This broad compatibility ensures that users can seamlessly integrate the device into their existing setups without any compatibility issues. The plug-and-play functionality simplifies the installation process, allowing users to start working within minutes of unpacking the device.

In terms of connectivity, the OL-6415-03 features a USB interface, ensuring fast and reliable communication with computers. The cable design minimizes clutter, further enhancing the workspace.

Overall, the 3Dconnexion OL-6415-03 stands out as a powerful tool that significantly improves navigation and control in 3D environments. With its advanced technologies, ergonomic design, and customizable features, it meets the demands of professionals looking for precision and efficiency in their 3D workflows. Whether used for detailed design work or complex visualization tasks, this 3D mouse is engineered to elevate the user experience to new heights.