Instructions for installation and modification
For the external dimensions of the appliance, see fig. S attached to the rear of the appliance and the table below.
Appliance, gross capacity of models (l) | Height H | |
see type plate |
| (mm) |
289 | (30..) | 1625 |
337 | (35..) | 1806 |
375 | (39..) | 2000 |
383 | (40..) | 1982 |
Installation instructions
Do not install the appliance
Changing over door hinges
Fig. T. The door hinges can be changed from one side to the other if required:
Only change over door hinges when mains plug is discon- nected!
WWith the door open, lever out plinth panel 1 on the hinge side with a screwdriver and remove from front.
-Lever out cover 2 with a screwdriver. Close door.
-Unscrew screw M5 3.
WPull hinge component 4 with hinge pin 5 out from under-
neath and remove.
-Open door, lift out at bottom and remove.
-Pull middle hinge pin 6out from underneath.
-Tilt out top door and lift off from underneath (with version I,
do not lose spacer sleeve 9).
WTransfer all hinge components onto the other side:
WTop: depending on version, proceed as follows:
Version I (visible operating panel): Lever out covers 8with a screwdriver at the front and remove at an angle from below. Remove hinge pin 7 and insert on the opposite side. Use the hexagon socket on the
into place at front.
Version II (concealed operating panel): Lift up cover 8 on handle side, push outwards; lift up cover on hinge side and
pull off.
-Unscrew earthing plate cm: first earthing screw cl, then inner retaining screw cq.
-Unscrew hinge 9: first undo earthing screw cl, then retai-
ning screws cq. Fit hinge 9to opposite side: for easy assem- bly, fit hinge from above and first tighten with the upper retai- ning screw cq M5, then screw cq and finally earthing screw cl M4.
-Turn earthing plate cm through 180° and screw tight again on the new handle side: first retaining screw cq, then earthing screw cl.
-Insert hinge pin 7 in the other retaining hole. Use the hexagon socket on the
-Fit covers 8 again: insert
wards and click into position; insert
WCentre: Change over cover bl with hinge bm: unscrew screws, lift off cover bl and hinge bm to the side, turn through 180° and replace on the other side, remove hinge bushing bn and
-Bottom: Using a screwdriver, remove the spacer bo, fig. T1, and replace on the other side.
W
- Remove plugs bp from the door mounting points and re- place on the other side.
-Suspend top door in hinge pin 7(with version I, do not lose spacer sleeve 9), close door.
-Slide middle hinge pin 6 into the door mounting from below through the hinge bm. Make sure the door is flush with the body of the appliance; adjust if necessary using the slots on the hinge.
-Suspend lower door, close.
-Rotate hinge component 4by 180°, remove hinge pin 5,
turn by 180° and replace. Mount both parts in the hinge bq: slide the pin into the door mounting through the hinge, tilt in the hinge component, slide up and attach with screw 3.
WAlign the door flush with the body of the appliance using the slot on the hinge bq, then tighten screw 3.
WAttach the plinth panel 1and click into place by pressing.
WWith the door open, insert the cover 2 in the plinth panel at the front and click into place at the back.
WTransfer* door handles br and plugs bt. With the door open, carefully lift out the pressure plates* bs at the front and slide away; unscrew handle using a Torx® or Phillips screwdriver*.
Reassemble in reverse order: replace the pressure plates and click into position.
Insertion into row of kitchen units
Fig. U. The appliance can be integrated into the kitchen units. To adapt the appliance to the height of the row of kitchen units, a suitable top cupboard can be fitted above the appliance 1.
For ventilation and air extraction, an exhaust air shaft at least 50 mm deep must be provided on the rear of the top cupboard over the entire width of the cupboard. The ventilation cross- section below the ceiling of the room should be at least 300 cm2. Generally, the bigger the cross section, the more economically the appliance operates.
WWhen integrating with standard kitchen units (depth max. 580 mm) and decor panels of up to max. 2 mm thick, the appliance can be installed directly next to the kitchen unit. The door of the appliance protrudes beyond the front of the kitchen unit 34 mm at the side and 51 mm in the centre of the appliance. This allows it to be opened and closed easily.
WWhen installing the appliance next to a wall 4, a distance on the hinge side of min. 36 mm is required between the appliance and the wall (handle projection with door open).
1Top cupboard | 3 | Wall of kitchen units |
2Refrigerator/freezer | 4 | Wall |
Note on fitting decor panel*
(with white appliances of height H = 1806 and 1982 mm) With decor panel and decor frame, you can adapt the appli- ance to the front of the kitchen units or contrast with them. The decor panels can be obtained from your kitchen furniture supplier. The decor frames can be retrofitted from your kitchen furniture supplier.
If you wish to fit the decor panel yourself, you require a drill or cordless screwdriver to
___________________________________________________
The manufacturer is continually working on the continous improvement of all types and models. We therefore hope for your understanding that we reserve the right to alter design, equipment and technology without notice.
20 | * depending on model and options |
CN/CNa..3 |