Liebherr 180613 7085462-00 manual Cleaning the appliance, Cleaning the IceMaker, Customer service

Page 12

Maintenance

u Pull out the power plug or switch off the fuse.

 

u Place cold storage accumulators on top of the frozen food.

u If possible, put the frozen goods in the freezer drawer,

wrapped in newspaper or a blanket, and store in a cool

place.

 

u Place a pan with hot, not boiling

 

water on a middle shelf.

 

-or-

 

u Half-fill the two lower drawers with

 

lukewarm water and put them in the

 

appliance.

 

w Defrosting is speeded up.

 

w Defrost water is collected in the drawers.

defrosting.

u Leave the door of the appliance open while

u Remove detached pieces of ice.

not run into the

u Pay attention that the defrost water does

kitchen unit.

 

u If necessary, pick up defrost water several times, using a

sponge or cloth.

 

u Clean the appliance (see 6.3) and rub dry.

 

6.3 Cleaning the appliance

 

CAUTION

Risk of injury and damage as a result of hot steam! Hot steam may damage the surfaces and cause burns. u Do not use any steam cleaners!

NOTICE

Incorrect cleaning damages the appliance!

u Do not use cleaning agents in concentrated form.

u Do not use any scouring or abrasive sponges or steel wool. u Please do not use any aggressive, scouring, sand-,

chloride-, chemical- or acid-based cleaning agents. u Do not use chemical solvents.

u Do not damage or remove the type plate on the inside of the appliance. It is important for the customer service.

u Do not pull off, bend or damage cables or other compo- nents.

u Do not allow any cleaning water to enter the drain channel, ventilation grille or electrical parts.

u Please use soft cleaning cloths and a universal pH-neutral cleaning agent.

u Please use cleaning and care products suitable for contact with foodstuffs in the appliance interior.

u Empty appliance.

u Pull out the power plug.

u Clean plastic outer and inner surfaces with lukewarm water and a little washing-up liquid.

u Clean drain hole: Remove deposits with a narrow instrument, e.g. a cotton bud.

u Most of the parts can be dismantled for cleaning: see the relevant chapter.

u Clean items of equipment by hand with lukewarm water and a little washing-up liquid.

u Only use a damp cloth to clean the telescopic rails. The grease in the runners is for lubrication purposes and must not be removed.

After cleaning:

u Wipe dry the appliance and items of equipment. u Connect the appliance and switch it on again. u Switch on SuperFrost (see 5.6.4) .

When the temperature is sufficiently cold: u Put the food back inside.

6.4 Cleaning the IceMaker*

The drawer of the IceMaker has to be emptied and slid in.

u To activate the setting mode: press the SuperFrost button Fig. 2 (12) for about 5 s.

w The display indicates c.

 

 

w The menu symbol Fig. 2 (16) shines.

freezer

compartment

u Using

the

Up setting button,

Fig. 2

(10)/

Down setting button,

freezer

compartment

Fig. 2 (11) select I.

u To confirm: press the SuperFrost button Fig. 2 (12). u Using the Up setting button, freezer compartment Fig. 2 (10)/ Down setting button, freezer compart-

ment Fig. 2 (11) select Ic.

u To confirm: press the SuperFrost button Fig. 2 (12).

u To deactivate the setting mode: press the On/Off button, freezer compartment Fig. 2 (8).

-or-

u Wait for 2 minutes.

w The temperature is indicated again in the temperature display.

u Remove the drawer.

u Clean the ice cube tray and drawer with warm water. If necessary, use mild washing-up liquid. Then rinse.

u Slide in the drawer again.

If washing-up liquid was used:

u throw away the first three loads of ice cubes to get rid of any remaining washing-up liquid.

Either leave the IceMaker switched off in this position or switch the IceMaker on again (see 5.6.10) .

6.5 Customer service

First check whether you can correct the fault yourself by refer- ence to the list (see Malfunction). If this is not the case, please contact the customer service whose address is given in the enclosed customer service list.

WARNING

Risk of injury if repair work is not carried out professionally!

u Have any repairs and action - not expressly specified - on the appliance and mains cable carried out by service personnel only. (see Maintenance)

u Read the appliance designation

Fig. 14 (1), service No. Fig. 14 (2) and serial No. Fig. 14 (3) off the type plate located inside the appliance on the left- hand side.

Fig. 14 u Notify the customer service, specifying the fault, appliance designation Fig. 14 (1), service No. Fig. 14 (2) and serial No.

Fig. 14 (3).

w This will help us to provide you with a faster and more accu- rate service.

u Keep the appliance closed until the customer service arrives.

w The food will stay cool longer.

12

Image 12
Contents Operating instructions Contents Appliance at a glanceAppliance at a glance General safety information General safety informationClimate For ambient temperatures Rating ConformityTemperature display Controls and displaysControls and displays Operating and control elementsPutting into operation Putting into operationControl Control Using adjustable bottle shelf Using the bottle holderVarioSafe Door racksBioFresh compartment Freezer compartment Drawers VarioSpaceInformation system Cold storage accumulatorsMaintenance MaintenanceDefrosting with NoFrost Manual defrostingCleaning the appliance Cleaning the IceMakerCustomer service After cleaningMalfunction MalfunctionSwitching off the appliance Taking the appliance out of serviceDecommissioning Decommissioning

180613 7085462-00 specifications

The Liebherr 180613 7085462-00 is an advanced product from Liebherr, known for its innovative engineering and high-quality construction solutions. This model embodies the company's commitment to excellence and efficiency in various industrial applications.

One of the primary features of the Liebherr 180613 7085462-00 is its robust design, which ensures longevity and durability in tough operating environments. The use of high-quality materials not only enhances the lifespan of the product but also contributes to its reliable performance under extreme conditions.

This model incorporates advanced technologies aimed at optimizing productivity. The Liebherr 180613 7085462-00 is equipped with an intuitive control system that allows for easy operation, making it accessible for a wide range of users. Additionally, its ergonomic design ensures that operators can work comfortably and efficiently, reducing fatigue and increasing overall productivity.

Another notable characteristic is the energy efficiency of the Liebherr 180613 7085462-00. The engineering team at Liebherr has integrated cutting-edge energy-saving technologies, which not only lower operational costs but also minimize the environmental impact. This is particularly important in today’s market, where sustainability is becoming increasingly critical.

The Liebherr 180613 7085462-00 also features advanced safety measures. With a focus on protecting both the operator and the machinery, the model incorporates several safety features that adhere to stringent industry standards. This ensures users can operate the machine with confidence, knowing their safety is a top priority.

In terms of versatility, the Liebherr 180613 7085462-00 can be used across various applications, from construction to logistics. Its adaptable design and extensive compatibility with other Liebherr components make it an ideal choice for businesses looking to streamline their operations.

Overall, the Liebherr 180613 7085462-00 is a testament to Liebherr’s engineering prowess. With its combination of robust design, advanced technologies, energy efficiency, and safety features, it stands out in the market as a reliable and versatile solution for a variety of industrial needs. Companies investing in this model can expect not only immediate operational benefits but also long-term value and efficiency.