Liebherr 7082 218-03 manual BioCool, Additional functions, SuperFrost, Interior light

Operation and control elements

BioCool

BioCool

The BioCool button switches the BioFresh compartment to maximum cooling.

It is recommended particularly if you wish to cool large quan- tities of food, freshly baked cakes or meals rapidly.

WSwitching on: Press the BioCool button bl briefly so that it lights up.

Note: The BioCool function uses slightly more energy. After approx. 6 hours, however, the electronic control system switches back automatically to normal energy-saving operation.

If required, the BioCool function can be switched off soo- ner.

WSwitching off: Press the BioCool button again until it goes out.

Additional functions

In set-up mode you can set the child-proof lock and adjust the brightness of the display*:

Activating set-up mode:

WPress SuperFrost button for approx. 5 secs - the Super- Frost button flashes - the display shows c for child-proof lock.

Note: the value to be altered flashes.

WSelect the required function by pressing the Up/Down button:

c = child-proof lock or h = brightness.

WNow select/acknowledge function by pressing SuperFrost button briefly:

•For c = child-proof lock, press the Up/Down button to select c1 = child-proof lock on or c0 = child-proof lock off and acknowledge with the SuperFrost button. When the symbol 6 is lit, the child-proof lock is activated.

•For h = brightness, press Up/Down button to select h1= minimum to h5 = maximum bright- ness and acknowledge with the SuperFrost button.

Exit set-up mode:

WTo exit the set-up mode, press the On/Off button; after

2 mins. the electronic system switches over automatically.

- The normal operating mode is activated again.

SuperFrost

Fresh food should be frozen to the core as rapidly as pos- sible. Frozen food can also be given a cold boost. This is provided by the SuperFrost facility 4 and ensures that the nutritional value, appearance and flavour of the food remain intact.

WThe maximum amount of food which can be frozen in 24 hours is shown on the type plate ("Freezing capacity

... kg/24h"), fig. A3, pos. 4. This amount varies accord-ing to the model and climate rating.

See "Freezing with SuperFrost" for more information.

Power failure/FrostControl display

If appears in the display, this means that the free- zer temperature has risen too high during the last few hours or days due to a power failure.

WIf you press the audible warning on/off button 5

whilst the display is reading , the highest temperature registered during the power failure will be displayed. Check the quality of the food and its suitability for con- sumption in case it has become too warm or even de-fros- ted.

-The highest temperature will appear for approx. 1 minute. After that, the actual temperature in the freezer will re-ap- pear. The "highest temperature" display can be switched off by pressing the audible warning on/off button.

Once the power is re-instated, the appliance will continue to operate at the most recent temperature setting.

Interior light

This switches off automatically after the door has been ope- ned for approx. 15 minutes. If it does not switch on when the door is opened briefly, but the temperature display is wor- king, the bulb may be defective.

Replacing the bulb:

WBulb data: max. 25 W; current and voltage must agree with the details on the type plate. Only use bulbs of the same size. Bulb fitting: E 14.

WSwitch off the appliance. Disconnect from the mains or remove or unscrew the fuse.

WPress the light cover together at the sides as in fig. F1 (1). Lift it out and unclip at back (2).

WReplace the bulb as in fig. F2. To counteract the friction of the lock washer, turn the bulb with slightly more pressure. When inserting the new bulb, ensure that the lock washer is properly in place in the lamp socket.

WClip the back end of the cover in and clip the sides into place.

16 BN/BNes...6