Instructions for installation and modification
Dimensions
The external dimensions of the appliance can be seen on the illustration on the opposite page (fig. S) and in the table
below. |
|
|
|
|
|
|
Gross capacity | External dimensions | [mm] |
| |||
of appliance [l] | A | B | C | D | E | F |
(see type plate) |
|
|
|
|
|
|
_____________________________________________________ | ||||||
258(26..) 1250 600 631 614 644 1179
309(31..) 1447 600 631 614 644 1179
362(36..) 1644 600 631 614 644 1179
413(42..) 1841 600 631 614 644 1179
_____________________________________________________
362(36..) 1644 660 683 662 704 1287
413(42..) 1841 660 683 662 704 1287
Installation instructions
- Do not install the appliance directly next to another refrig- erator or freezer. This is important to prevent condensa- tion and consequential damage resulting from it.
-This does not apply to
The "Installation instructions for
Changing over door hinges
On appliances which are intended for individual installation the door hinges can be changed from one side to the other. On SBS appliances in stainless steel finish, which are de- signed for
WOnly change over door hinges when mains plug is dis- connected!
WFig. T. With the door open, lever out plinth panel 1 on the hinge side with a screwdriver and remove from front.
-Lever out cover 2 with a screwdriver. Close door.
-Unscrew screw M5 3.
WPull hinge component 4 with hinge pin 5 out from un- derneath and remove.
WOpen door, lift out at bottom and remove; do not lose the spacer bl.
WTransfer all hinge components onto the other side:
WTop: depending on version, proceed as follows:
Version I (visible operating panel): Lever out covers 8 with a screwdriver at the front and remove at an angle from below. Remove hinge pin 7 and insert on the op- posite side. Use the hexagon socket on the open-ended spanner provided (spanner width 5). Fit covers 8 again: insert at rear and click into place at front.
Version II (concealed operating panel): Lift up cover 8 on handle side, push outwards; lift up cover on hinge side and pull off.
-Unscrew earthing plate cm: first earthing screw cl, then inner retaining screw cq.
-Unscrew hinge 9: first undo earthing screw cl, then re-
taining screws cq. Fit hinge 9 to opposite side: for easy assembly, fit hinge from above and first tighten with the upper retaining screw cq M5, then screw cq and finally earthing screw cl M4.
-Turn earthing plate cm through 180° and screw tight again on the new handle side: first retaining screw cq, then earthing screw cl.
-Insert hinge pin 7 in the other retaining hole. Use the hexagon socket on the open-ended spanner provided (spanner width 5).
-Fit covers 8 again: insert hinge-side cover by sliding outwards and click into position; insert handle-side cover by sliding inwards and click into position.
-Bottom: Using a screwdriver, remove the spacer bo and replace on the other side, fig. T1.
WRe-attach the door:
-Remove plugs bp from the door mounting points and replace on the other side.
-Only on 1644 mm and 1841 mm high
same screw dn. Discard the old closure dl (or keep it for later use).
-Suspend door with spacer in hinge pin 7, close door.
-Rotate hinge component 4 by 180°, remove hinge pin 5, turn by 180° and replace. Mount both parts in the hinge bq: slide the pin into the door mounting through the hinge, tilt in the hinge component, slide up and attach with screw 3.
WAlign the door flush with the body of the appliance using the slot on the hinge bq, then tighten screw 3.
WAttach the plinth panel 1 and click into place by pressing.
WWith the door open, insert the cover 2 in the plinth panel at the front and click into place at the back.
WTransfer* door handle br and plugs bt. With the door open, carefully lift out the pressure plates* bs at the front and slide away; unscrew handle.
Reassemble in reverse order: replace the pressure plates and click into position.
16 | * Depending on model and options | K/SK/es..0 |
|