Wayne-Dalton 44 Label Placement, To 7/8, Torsion spring tags one per spring

Page 17

3/4” To 7/8”

3/4” To 7/8”

 

Door edges

 

Horizontal tracks

Rear center

Horizontal

back hang

track(1) 3/8” Truss head bolt (may not be supplied)

(1) 3/8” Nut

(may not be supplied)

Horizontal

track

Drill 3/8”

diameter hole

Center of the horizontal track

26

Label Placement

Tools: Step Ladder

IMPORTANT: Using the illustration, attach the appropriate labels to the ap- propriate location on the section, as shown.

NOTE: The Spring Warning tag(s) are factory attached (one per spring).

NOTE: Because of different configurations, some labels may require minor relocations.

Torsion spring tag(s) (one per spring)

WARNING

Residential Dust label

(For California Residents Only)

Residential

warning label

WARNING

HIGH SPRING TENSION CAN CAUSE

SERIOUS INJURY OR DEATH.

DO NOT adjust, repair or remove springs or parts to which springs are connected, such as steel brackets, cables, wood blocks, fasteners or other parts of the counterbalance system.

Adjustments or repairs must ONLY be made by a trained door systems technician using proper tools and instructions.

DO NOT remove, cover or paint over this tag. Product user should inspect this tag periodically for legibility and should order a replacement tag from the door manufacturer, as needed.

WARNING

Lift handles/gripping points are required on this door, located as spelled out in the installation instructions, even if the door is motor operated.

Failure to install and use these lift handles/

 

 

gripping points on this door can result in

 

 

serious injury to fingers and/or hands, if

 

 

placed in the opening between sections,

 

IMPORTANT

when the door is operated manually.

 

WARNING

 

THIS WOOD PRODUCT REQUIRES PROPER

 

ACC0RDANCE TO THE DIRECTIONS GIVEN IN THE

 

 

FINISHING PRIOR TO ANY DOOR HARDWARE BEING

 

 

APPLIED. BOTH INNER AND OUTER FACES OF THE

 

 

SECTION(S), AS WELL AS ALL EDGE SURFACES

 

important notice

MUST BE PREPARED AND FINISHED IN STRICT

The adjacent bottom corner bracket and

AND/OR DELAY IN FINISHING, THAT ALLOWS FOR

Wood label

MANUAL UNDER “MAINTENANCE AND PAINTING

 

INSTALLATION INSTRUCTIONS AND OWNER’S

all cable retention features including

 

INSTRUCTIONS FOR ALL WOOD DOORS”.

milford pins, cotter pins, & clevis pins are

 

IMPROPER STORAGE, IMPROPER TRANSPORTATION

under HIGH SPRING TENSION.

 

THE EXPOSURE OF THIS WOOD PRODUCT TO

Adjustments and repairs must only be

 

THE LIMITED WARRANTY.

 

 

MOISTURE AND/OR OTHER CONTAMINANTS, VOIDS

made by a trained door systems

 

 

technician, using proper tools and

 

 

instructions.

 

 

DO NOT REMOVE, COVER OR PAINT OVER

 

 

THIS LABEL. PRODUCT USER SHOULD

 

 

INSPECT THIS LABEL PERIODICALLY FOR

 

 

LEGIBILITY AND SHOULD ORDER A

 

 

REPLACEMENT FROM THE DOOR

Bottom section warning labels

MANUFACTURER AS NEEDED.

Lift handles/gripping points are required on this door, located as spelled out in the installation instructions, even if the door is motor operated.

Failure to install and use these lift handles/ gripping points on this door can result in serious injury to fingers and/or hands, if placed in the opening between sections, when the door is operated manually.

WARNING

The adjacent bottom corner bracket and all cable retention features including milford pins, cotter pins, & clevis pins are under HIGH SPRING TENSION.

Adjustments and repairs must only be made by a trained door systems technician, using proper tools and instructions.

DO NOT REMOVE, COVER OR PAINT OVER THIS LABEL. PRODUCT USER SHOULD INSPECT THIS LABEL PERIODICALLY FOR LEGIBILITY AND SHOULD ORDER A REPLACEMENT FROM THE DOOR MANUFACTURER AS NEEDED.

17

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Graduated End Hinge And Strut Identification B l e O f C o n t e n t sStacked Sections C1. Top Section Graduated End HingesPackage Contents Important Safety Instructions Tools RequiredDoor Section Identification Graduated End Hinge Strut IdentificationGraduated End Hinge Schedule Top Preparing the Opening Removing an Existing DoorBackroom Requirements Headroom RequirementsHeader board 2x Lumber preferred Min. side HeadroomRoom Clearance for Track isPage Graduated End And Center Hinges Track Roller CarriersStrutting Top Fixtures Half Center HingesBottom Section Vertical TracksTop Section Stacking SectionsIf you have 3 vertical tracks For Graduated end hinges and Center HingesHorizontal Tracks Adjusting Top FixturesEnd Bearing Brackets Center Bracket16 x 2 tamper-resistant lag screw Torsion Spring AssemblySprings, must be positioned, as shown Hole of the center bracketsTorsion Spring Attachment For Doors with a Coupler AssemblyIf your door came with a Center Bracket Bushing If your door came with a Center Bearing BracketsSet Collars Winding SpringsRear Back Hangs Tools Step Ladder, 3/8 Wrench16-18 x 1-1/4 Parallel to door Ceiling memberTorsion spring tags one per spring Label PlacementTo 7/8 Door Arm Hookup Tools Power drill, 1/8 Drill bit, Tape measureLift Handles Pull Down RopeOperation and Maintenance Cleaning Your Garage DoorPainting Your Garage Door Clear Or Stained FinishesPage Limited warranty Double Flush, Model Warranty
Related manuals
Manual 18 pages 38 Kb

44 specifications

The Wayne-Dalton 44 is a notable garage door known for its durability, versatility, and aesthetic appeal. Designed to meet a range of residential needs, this model combines innovative technology with robust features. Its construction primarily utilizes high-quality steel, ensuring long-lasting performance and security. The durability of the Wayne-Dalton 44 makes it an ideal choice for homeowners looking for a reliable garage door that can withstand the elements.

One of the standout features of the Wayne-Dalton 44 is its extensive range of customizable options. Homeowners can select from various styles, colors, and finishes, allowing them to match their garage door with the design of their home. Whether one prefers a traditional look or a more contemporary design, the Wayne-Dalton 44 offers flexibility to accommodate diverse architectural styles.

In terms of insulation, the Wayne-Dalton 44 is equipped with advanced insulation technology, making it energy-efficient. Its insulated models provide an extra layer of protection against harsh weather conditions, which helps maintain a stable internal temperature within the garage. This feature not only enhances comfort but also contributes to energy savings over time.

Wayne-Dalton has also integrated safety technologies into the design of the 44 series. The door is equipped with an advanced safety sensor system that detects obstacles, preventing accidents when the door is in motion. This is especially important for families with children or pets, as it adds an extra layer of peace of mind.

Another significant characteristic of the Wayne-Dalton 44 is its low maintenance requirements. The use of high-quality materials and finishes means that the door is resistant to rust and corrosion, reducing the need for frequent upkeep. Additionally, the door’s operation is notably quiet, which is an attractive feature for those who value tranquility at home.

Overall, the Wayne-Dalton 44 garage door exemplifies a perfect blend of style, functionality, and cutting-edge technology. With its focus on customization, insulation, safety, and low maintenance, it stands out in the market, offering an excellent balance for homeowners seeking a reliable and attractive garage door solution.
Top Page Image Contents