Wayne-Dalton 44 Graduated End Hinge Strut Identification, Door Section Identification

5/16” x 1-1/4”		Cotter pin		Cable drums RH/LH Torsion springs RH/LH
Clevis pin (as required)		(as required)
End bearing	End bearing brackets		Center bearing bracket		Center bracket bushing
brackets RH/LH
(as required)	RH/LH (as required)		assembly (as required)		assembly (as required)

Center coupler	Key shafts		Set collars	Counterbalance lift cables
assembly (as required)	(as required)	(as required)
Strut clips	Hinges		Half Center	Weather seals
(as required)		hinges (as required)		& nails (If included)
Bottom weather seal with	Lift handles		Pull down rope	1/4”-20 x 9/16”
3/4” nails (as required)	(as required)		(if included)	Track bolts (as required)
(2) 3/8”-16 x 3/4”				1/4” - 14 x 1”
Truss head bolts	(2) 3/8”- 16 Hex nuts			Lag screws (as required)
			5/16” x 2” Tamper-resistant hex head
				lag screw (as required)

The BOTTOM SECTION can be identified by #1.

The INTERMEDIATE I SECTION can be identified by #2.

The INTERMEDIATE II SECTION can be identified by #3, for a 4 section high door only. The INTERMEDIATE III SECTION can be identified by #4, for a 5 section high door only. The INTERMEDIATE IV SECTION can be identified by #5, for a 6 section high door only. The INTERMEDIATE V SECTION can be identified by #6, for a 7 section high door only. The INTERMEDIATE III SECTION can be identified by #7, for a 8 section high door only. The TOP SECTION can be identified by a #, being the highest section.

Typical design option “Outside surface of		Top rail
door sections shown”
3. Top		Outside	Inside
section		surface	surface
			Typical
2.			stamping
	#	#	location		1
Intermediate
section(s)		Bottom	Bottom
		rail	rail
1.		Side views of sections
Bottom	Top	Intermediate(s)		Bottom
section	section			section
NOTE: 3 Section high doors, does not have
an Intermediate II Section.

Graduated End Hinge And

Strut Identification

Graduated End Hinge Schedule

Door Height	Track	Section Type	Graduated End Hinge
			Number
		Top	N/A
	2”	Intermediate I	#2
3 Section High Door		Bottom	#1
		Top	N/A
	3”
		Intermediate I	#4
		Bottom	#3

5/16” x 1 5/8” Hex head lag screws (as required)

1/4” - 10 x 1” Tamper-resistant hex head lag screw (as required)

1/4”- 20 Flanged

hex nuts (as required)

3/8”-16 x 1-1/2” Hex bolts

1/4” - 20 x 2 1/2”

Carriage bolts (as required)

		Top	N/A
	2”	Intermediate II	3#
Intermediate I		2#
4 Section High Door		Bottom	1#
		Top	N/A
	3”	Intermediate II	5#
		Intermediate I	4#
		Bottom	3#
		Top	N/A
		Intermediate III	4#
	2”
		Intermediate II	3#
		Intermediate I	2#
5 Section High Door		Bottom	1#

1/4”-20 x 7/8” Self	5/16” x 1 5/8” Hex head lag screws
drilling screws (as required)	(as required)

Door Section Identification

When installing your door, you must use sections of the appropriate height in the right stacking location. Determine, what sections you need to use in what order depends on the design of your door.

Sections are stamped for identification, #1, #2, #3, #4, #5, #6, #7, and #8. The stamp, located on each side of the sections identifies the stacking sequence. The sequence is always deter- mined by #1 being the bottom section to #7 or #8 being the highest top section. If the stamp on the section is illegible, refer to the section side view illustration. The section side view illustration shows the section profile of all sections, and can also be used to identify each section.

	Top	N/A
	Intermediate III	6#
3”
	Intermediate II	5#
	Intermediate I	4#
	Bottom	3#

4

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com