Hoover HND 615 SI manual Identifying Minor Faults, Fault Cause Remedy

IDENTIFYING MINOR FAULTS

Should the dishwasher fail to operate, before contacting the Service Centre, make the following checks:

FAULT	CAUSE	REMEDY
	Plug is not connected to wall	Connect electric plug
	socket
1 - Machine completely dead	O/I button has not been pressed	Press button
	Door is open	Close door
	No electricity	Check the fuse in the plug and
		the electricity supply
	See causes for no. 1	Check
	Water tap is turned off	Turn water tap on
2 - Machine does not	Programme selector is not at	Turn programme selector to
draw water	correct position	correct position
	The inlet hose is bent	Eliminate the bends in the hose
	The inlet hose filter is not	Clean the filter at the end of the
	correctly connected	hose
	Filter is dirty	Clean filter
	Outlet hose is kinked	Straighten outlet hose
3 - Machine does not	The outlet hose extension is	Follow the instructions for
discharge water	not correctly connected	connecting the outlet hose
		carefully
	The outlet connection on the	Call a qualified technician
	wall is pointing downwards not
	upwards
4 - Machine discharges	Position of outlet hose is too	Lift outlet hose to at least 40 cm
water continuously	low	above floor level
	Excessive amount of detergent	Reduce amount of detergent
		Use suitable detergent
5 - Spray arms are not heard
	Item prevents arms from rotating	Check
to rotate
	Plate and cup filter very dirty	Clean plate and cup filter
6 - On electronic appliances	Water inlet tap turned off	Switch off the appliance.
without a display: one or		Turn on the tap.
more LED flashing quickly.		Re-set the cycle.

FAULT	CAUSE	REMEDY
	See causes for no. 5	Check
	Bottom of saucepans have not	Burnt on food remains must
	been washed well	be soaked before putting pans
		in dishwasher
	Edge of saucepans have not	Reposition saucepans
	been washed well
	Spray arms are partially blocked	Remove spray arms by
		unscrewing ring nuts clockwise
		and wash under running water
7 - Load of dishes is only	The dishes have not been	Do not place the dishes too
partially washed	properly loaded	closely together
	The end of the outlet hose is in	The end of the outlet hose
	the water	must not come into contact
		with the outflow water
	The incorrect amount of	Increase the measure
	detergent has been measured	according to how dirty the
	out; the detergent is old and hard	dishes are and change detergent
	The wash programme is not	Choose a more vigorous
	thorough enough	programme
	The lower basket dishes have	Depress half load button
	not been washed
8 - Presence of white spots	Water is too hard	Check salt and rinse aid level
		and regulate amount.
on dishes		Should the fault persist,
		Contact Service Centre
	The dishes knock against one	Re-check loading of dishes in
9 - Noise during wash	another	the basket
	The revolving arms knock against	Again re-check loading
	the dishes
10 - The dishes are not	Inadequate air flow	Leave the dishwasher door ajar
		at the end of the wash program
completely dry
		to allow the dishes to dry naturally
N.B.: Should any of the situations	occur and should the machine	give a bad wash performance,

it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the deposits which a second wash in the machine would not be able to remove.

If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher. This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee.

This information will make it possible to take more effective action more quickly.

The manufacturers decline any responsibility for any printing mistakes in this instruction booklet. They also reserve the right to modify their own appliances as necessary without altering the essential characteristics.

28 29