Hoover HND 615 manual Changing a running program, Program operations, Program end, Option button

Page 13

Changing a running program

Proceed as follows to change or cancel a running program:

■Hold down the current program button (with the LED on) for at least 3 seconds. The program LEDs (except for the "RAPID" program LED) will blink until all water is drained (if necessary).

The running program will be cancelled and the corresponding LED will start to blink.

IMPORTANT

To cancel the "COLD RINSE" program, simultaneously hold down the "RAPID" program button and "HALF LOAD" option button (the relevant LEDs will blink to confirm cancellation).

■At this point a new program can be set.

WARNING!

Before starting a new programme, you should check that there is still detergent in the dispenser.

If necessary, top up the dispenser.

If there is any break in the power supply while the dishwasher is operating, a special memory stores the selected programme and, when the power is restored, it continues where it left off (if it is necessary, the appliance will make a short thermal anti-shock programme before).

Program operations

When a program is running the relevant LED will remain on and the 3 “PROGRAM STATUS” LEDs ("WASH", "RINSE", and "DRY") will light singularly and in sequence to indicate the current phase.

Program end

The “PROGRAM STATUS” LEDs will turn off and the selected program LED (2 LEDs for the "COLD RINSE" program) will blink to indicate that the cycle has ended.

Dishes can now be removed and the dishwasher turned off by pressing the "ON/OFF" button or dishes can be loaded for new cycle.

Option button

"HALF LOAD" button

By using this option, it is possible to wash a smaller quantity of crockery: you should load only the upper basket for dishes and place cutlery in the tray in the bottom basket.

This reduces water and energy consump- tion and requires a smaller quantity of detergent.

IMPORTANT

This button MUST be set BEFORE the program starts.

"DELAY START" button

Dishwasher start time can be set with this button, delaying the start by 3, 6 or 9 hours.

Proceed as follows to set a delayed start:

■Press the "DELAY START" button (each time the button is pressed the start will be delayed by 3, 6 or 9 hours respectively and the corresponding time LED will light).

■To start countdown, press the selected program button (the relevant LED will stop blinking and remain on, while the set time LED will start to blink).

If a 9 hour delay is set, countdown will be displayed by the 6h LED after 3 hours and the 3h LED after 6 hours.

At the end of the last 3 hours (at the end of countdown) the 3h LED will stop blinking and remain on to indicate the washing phase and the program will start automatically.

If countdown has not ended, whereby the program has not yet started, it is possible to change or cancel the delayed start and select another program or to select/unselect the option button, proceeding as follows:

■Hold down the selected program button for at least 5 seconds (the corresponding LED will start to blink while the set time LED will stop blinking and remain on).

■Press the "DELAY START" button to set another delayed start time (the corresponding time LED will turn on) or cancel delayed start (corresponding time LEDs will all turn off).

■A new program can be set after a delayed time has been changed or cancelled (the corresponding LED will stop blinking and remain on) or an option button has selected or deselected.

Fault signals

If malfunctions or faults occur when a program is running the LED that corresponds to the selected cycle (2 LEDs for the "COLD RINSE" program) will blink rapidly.

In this case, turn the dishwasher off by pressing the "ON/OFF" button. After checking to make sure the water intel hose tap is open, that the drain hose is not bent and that the siphon or filters are not clogged, set the selected program again. If the anomaly persists, contact Customer Service.

IMPORTANT

This dishwasher is equipped with an anti-overflow safety device which will automatically empty any excess water should a problem occur.

WARNING!

To ensure the correct operation of the anti-overflow safety device, it is recommended not to move or to tilt the dishwasher during operation.

If it is necessary to move or to tilt the dishwasher, first make sure the washing cycle is finished and that no water is left in the tank.

24

25

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Instruction Book Fig. a ContentsInstallation Safety InstructionsWater connection Connecting the outlet hoseWater Softener Unit Installation in Fitted KitchensType Loading the salt Salt loading indicatorNever Lift or Lower the Basket by ONE Side only Using the lower basket Using the upper basketLoading Dishes International place load Ref. EN 50242 Standards Information for the Test LaboratoriesFilling the detergent container Loading the Detergent and the Rinse AIDNormal wash Filling the rinse aid containerPratical Hints Cleaning the FiltersWhen Cycle is Finished Cleaning MaintenanceTechnical Data DimensionsDescription of the Control Program Selection and Special FunctionsChanging a running program Fault signalsProgram operations Program endProgramme Description Check list Programme contentsProgramme standardised to EN Wash with prewashFault Cause Remedy Identifying Minor FaultsHoovercare 08705-400600

HND 615, HND 615 SI specifications

The Hoover HND 615 SI is a highly efficient and versatile washing machine that has garnered attention for its innovative features and advanced technology. Designed to cater to the needs of modern households, this model combines practicality with a sleek aesthetic, making it a popular choice for consumers looking for reliability and performance.

One of the standout features of the HND 615 SI is its extensive wash program selection. With multiple settings tailored for various fabric types and soil levels, users can customize their laundry experience to ensure optimal cleaning results. The machine is equipped with programs for cotton, synthetics, delicate fabrics, and even a quick wash option, allowing users to save time on less-soiled items.

The HND 615 SI also boasts a high energy efficiency rating, which is essential in today’s eco-conscious market. By using innovative technologies, this washing machine reduces water and energy consumption without compromising on performance. This eco-friendly approach not only helps in lowering utility bills but also contributes to environmental sustainability.

Another notable characteristic of the HND 615 SI is its innovative steam cleaning technology. This feature enhances the washing process by reducing wrinkles and allergens in clothing, making it an excellent option for households with sensitive skin or allergy sufferers. The steam function provides a deeper clean while also minimizing the need for ironing, thereby saving time and effort.

Additionally, the Hoover HND 615 SI incorporates a variable spin speed that allows users to adjust the intensity based on their clothing needs. The machine's impressive spin speed ensures that clothes come out nearly dry, reducing drying time significantly. Furthermore, the inverter motor technology makes the washing machine quieter and more durable, providing a more pleasant laundry experience.

With a user-friendly digital display, the HND 615 SI makes it simple for users to monitor and control their washing cycle. This interface typically includes options for delayed start times, allowing for increased flexibility in managing laundry schedules.

In summary, the Hoover HND 615 SI is a sophisticated washing machine that combines efficient cleaning technology, energy conservation, and user-friendly features. Its array of wash programs, steam cleaning capability, and adjustable spin speed make it an ideal choice for those seeking convenience and effectiveness in their laundry routines.
Top Page Image Contents