JBL P81, P941 Slide the baffle into place in the mounting frame, Remove the frame alignment tool

Page 9

7.Be sure to run the speaker wire in through the rear opening before reinstalling the baffle assembly.

8.Insert the mounting frame into the cutout until the clamps snap into place.

CLAMP

Mounting Frame

Clamp

rameF Alignment Tool

14.Make speaker wire connections. Refer to the Making Connections section on page 11 for instructions.

15.Slide the baffle into place in the mounting frame.

Note how the clamp springs open

Figure 13: Clamp Close-Up

rt f Inse rame into wall opening

A

rewS

Clamp

allW

B

Figure 15: Frame Alignment Tool

9.Insert the frame alignment tool horizontally into the center of the frame. This tool functions as a frame spreader, while the clamps are being tightened, as shown in Figure 15.

10.Starting from the lower right corner and working in a diagonal torque sequence, use a power screwdriver to tighten each of the clamp screws (only until almost snug). If needed, adjust the mounting frame so it is level and centered in the cutout.

11.Perform a final torque sequence. Hand-tighten frame screws and check each screw at least twice to make sure they are fully tightened to prevent rattles.

12.Remove the frame alignment tool.

13.Place the included fiberglass insula- tion in the back of the mounting frame, as shown in Figure 16. Cut an “x” into the insulation and thread the wire(s) through.

Figure 17: Tighten Allen Screws With Allen Key Wrench

NOTE: Be sure that the speaker wires are clear of the woofer basket and not too close to the woofer cone. Make sure the wires are not pinched between the baffle and the mounting frame. Refer to Figure 16.

16.Use the spacer shim to center the baffle inside of the frame while securing with four 10-32 x 2-1/4-inch screws. Loosely tighten the screws while using the spacer on the bottom side. Remove spacer and gauge the other three sides before starting final torque sequence. Proper cen- tering of the baffle is critical to the grille fitting properly.

17.Use the included 5/32-inch Allen key to tighten until snug, as shown in Figure 17.

C

Figure 14: Clamp Mechanism

Fiberglass Insulation

Allen Head

Screws

Baffle

Assembly

Thread Speaker Wires

Figure 16: Install the Insulation and Baffle

10

Page 8 Page 10
Image 9
Page 8 Page 10
Contents P81 P941 Documentation Conventions P81/P941 IN-WALL LoudspeakersProduct Registration P81/P941 HighlightsIntroduction Exceptional accuracyUnpacking Invert speaker so it is in the upright positionScrim Cloth Tweeter Loudspeaker OverviewHigh-Frequency Tilt Control WooferInput Connectors Filter NetworkInput Panel Installation Considerations Loudspeaker PlacementP81 and P941 should be installed by a professional Rear wall, as shown in FigureInstallation Instructions To Install the P81/P941Locate the wall studs Remove the frame alignment tool Slide the baffle into place in the mounting frameTo Make Connections Making ConnectionsTo optimize the P81 and P941 for best performance Optimizing PerformanceBegin playback of a familiar music or film source Apply one to two coats of paint for desired finishTo Paint the Grille Loudspeaker Volume LevelsTo Attach the Grille To Remove the GrilleObtaining Service P81/P941 SpecificationsIndex Harman International Company

P81, P941 specifications

JBL has long been synonymous with high-quality audio products, and their P941 and P81 models are no exception. These headphones cater to audiophiles and casual listeners alike, offering a balanced blend of performance, comfort, and innovative technology.

The JBL P941 is designed to deliver an immersive listening experience, featuring advanced Bluetooth connectivity that ensures seamless pairing with a wide range of devices. This model boasts a sleek, ergonomic design, which not only enhances comfort during extended use but also adds a touch of elegance to its aesthetic. The P941 incorporates JBL’s signature owlsound technology, where sound precision meets powerful bass delivery, allowing users to experience their favorite tracks with remarkable clarity.

The headphones come equipped with active noise-cancellation technology, which significantly reduces ambient noise, making them ideal for use in crowded environments or during travel. Alongside this, the P941 offers an impressive battery life, providing up to 30 hours of continuous playtime on a single charge. The rapid charge feature is particularly noteworthy, allowing for quick power-ups when needed. Additionally, they include integrated voice assistant support, enabling users to control music playback and access information hands-free.

On the other hand, the JBL P81 sets itself apart with its lightweight build and portable features. This model is targeted toward users who value flexibility without compromising sound quality. The P81 includes JBL Pure Bass technology, which delivers deep, punchy bass that is sure to please any music lover. The headphones offer a customizable fit due to their adjustable headband and rotating ear cups, ensuring comfort during long listening sessions.

The battery performance of the P81 is competitive, providing about 25 hours of playback time and quick charging capabilities. This model also emphasizes user interaction, with touch controls seamlessly integrated into the ear cups for easy navigation.

Both models come with a dedicated app, allowing users to personalize their sound preferences and update firmware. Whether you opt for the P941 or the P81, you can expect JBL’s commitment to quality, innovation, and a premium audio experience that caters to various listening styles. With their combination of comfort, outstanding sound quality, and practical features, these headphones are ideal choices for music lovers on the go.
Top Page Image Contents