Smeg LSA643XPQ instruction manual User instructions

Page 19
Manual background

User instructions

Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system.

When necessary, refill the regenerating salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion.

Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damage the water softening system.

ADDITIONAL FUNCTIONS (Customizing the consumer parameters) (available in all programs except the soak program)

The electronic control system allows personalizing the machine use directly through a programming procedure not directly accessible that allows: regulate water hardness level.

To access the programming environment, the appliance must be turned on with the door closed. Then proceed as follows:

press the PROGRAM DELAY (6) button until the H symbol appears on the display, followed by the number 3, > H3;

press the PROGRAM DELAY (6) button the number of times needed to select the right setting level for the hardness of the water (H0, H1, H2, H3, H4, H5);

press the START/STOP (7) button to confirm the setting and return to the program setting menu.

N.B.: after 2 minutes, the appliance exits the parameter setting menu automatically.

18

Image 19
Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. Safety and operating instructions Safety instructionsTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS 2. Installation and hook-up Installation instructionsFor free-standing models only 2.1 Water supply connection CONNECTING TO THE WATER SUPPLYDRAIN CONNECTION IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD 2.2 Electrical connection and precautionsFOR GREAT BRITAIN ONLY Fuse replacement3.1 Front panel User instructions3. Description of the controls 7 START/STOP BUTTON 8 POWER ON LIGHTDURATION PROGRAMME NUMBER & SYMBOLLOAD CROCKERY PROGRAMLIGHTING 3.3 Washing programsBefore starting a washing program make sure that The correct amount of detergent has been added to the dispenserINTERRUPTING A PROGRAM SELECTION PROGRAMSTART PROGRAM END PROGRAMSTOPPING A PROGRAM TO CHANGE A PROGRAMParticularly, on the display it will have the following indications HALF LOAD WASH FUNCTION on some models only TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENTREMOVING THE DISHES 4.1 Using the water softening system 4. Operating instructionsUser instructions WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensersADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTINGDuring the washing cycle, the dispenser will be opened automatically ADDING THE DETERGENTUser instructions Correct loading of the dishes helps ensure optimal washing results 4.3 General warnings and recommendationsMAKE SURE that the items being washed are dishwasher-safe Dishes and objects in copper, tin, zinc or brass these tend to stain Items which are not dishwasher-safeLOWER BASKET 4.4 Using the basketsLOADING THE LOWER BASKET CUTLERY BASKET LOADING THE UPPER BASKET UPPER BASKETDepending on the models, the basket may be equipped with some or all of the following accessories Version B ADJUSTING THE UPPER BASKETUser instructions 5.1 General warnings and recommendations 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER CLEANING THE SPRAY ARMSFill the rinse aid dispenser Shut off the water supply tap CLEANING THE FILTER UNITGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE PROLONGED DISUSEReconnect the water intake hose and open the tap again TROUBLESHOOTING MINOR PROBLEMSIf the dishes are not being cleaned properly, check that BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSEIf the dishes show signs of streaking, staining, etc., check that If the dishes fail to dry or remain dull, check thatIf there are visible traces of rust inside the tank E1 E2 E3 E4 E5 E6 E7 E8 E9 6. TroubleshootingTABLE OF FAULTS DETECTED BY THE SELF-DIAGNOSTICS SYSTEM FAULTCapacity TECHNICAL DATAElectrical characteristics Widtheinstellen mollelaterali primadell’installazionedes ressortslateraux avant l’installation Montare la porta e regolarelatensione delle