Smeg LSA643XPQ instruction manual User instructions, To Change A Program, Stopping A Program

Page 14
TO CHANGE A PROGRAM

User instructions

At this point,it is possible to start the cycle again, otherwise:

TO CHANGE A PROGRAM

To change the running program it is necessary:

to interrupt the running program (see “INTERRUPTING A PROGRAM”);

select the new program;

to press again the START/STOP button (7) to make start the new program.

STOPPING A PROGRAM

To stop a program in progress, it must first be interrupted (see

"INTERRUPTING A PROGRAM").

Now press buttons P1+P2 simultaneously and the first three program lights will come on.

The display will show "P0" and the dishwasher will immediately switch to the end of the cycle and drain the tank (during this process, the "Time to end" message will flash). When the drain procedure ends, the end of cycle message "End" appears on the display.

In case that the door is opened during the operation, to the next door closing it is going to be necessary to start the program as shown in paragraph “START PROGRAM”. The program will resume from the point in which it was interrupted.

In case that the tub temperature is higher than 50°C the program will start about 30 seconds later.

The washing cycle will not take place if the dishwasher door is left open or not properly closed.

13

Image 14
Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents Safety instructions 1. Safety and operating instructionsTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS For free-standing models only Installation instructions2. Installation and hook-up DRAIN CONNECTION CONNECTING TO THE WATER SUPPLY2.1 Water supply connection 2.2 Electrical connection and precautions IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORDFuse replacement FOR GREAT BRITAIN ONLY7 START/STOP BUTTON 8 POWER ON LIGHT User instructions3. Description of the controls 3.1 Front panelPROGRAM PROGRAMME NUMBER & SYMBOLLOAD CROCKERY DURATIONThe correct amount of detergent has been added to the dispenser 3.3 Washing programsBefore starting a washing program make sure that LIGHTINGEND PROGRAM SELECTION PROGRAMSTART PROGRAM INTERRUPTING A PROGRAMTO CHANGE A PROGRAM STOPPING A PROGRAMParticularly, on the display it will have the following indications HALF LOAD WASH FUNCTION on some models only REMOVING THE DISHES TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENTTO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT 4. Operating instructions 4.1 Using the water softening systemUser instructions 4.2 Using the rinse aid and detergent dispensers WATER HARDNESS TABLEADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AIDADDING THE DETERGENT During the washing cycle, the dispenser will be opened automaticallyUser instructions MAKE SURE that the items being washed are dishwasher-safe 4.3 General warnings and recommendationsCorrect loading of the dishes helps ensure optimal washing results Items which are not dishwasher-safe Dishes and objects in copper, tin, zinc or brass these tend to stainLOADING THE LOWER BASKET 4.4 Using the basketsLOWER BASKET CUTLERY BASKET UPPER BASKET LOADING THE UPPER BASKETDepending on the models, the basket may be equipped with some or all of the following accessories ADJUSTING THE UPPER BASKET Version BUser instructions CLEANING THE SPRAY ARMS 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER 5.1 General warnings and recommendationsPROLONGED DISUSE CLEANING THE FILTER UNITGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE Fill the rinse aid dispenser Shut off the water supply tapBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE TROUBLESHOOTING MINOR PROBLEMSIf the dishes are not being cleaned properly, check that Reconnect the water intake hose and open the tap againIf there are visible traces of rust inside the tank If the dishes fail to dry or remain dull, check thatIf the dishes show signs of streaking, staining, etc., check that FAULT 6. TroubleshootingTABLE OF FAULTS DETECTED BY THE SELF-DIAGNOSTICS SYSTEM E1 E2 E3 E4 E5 E6 E7 E8 E9Width TECHNICAL DATAElectrical characteristics CapacityMontare la porta e regolarelatensione delle mollelaterali primadell’installazionedes ressortslateraux avant l’installation einstellen