Smeg LSA643XPQ instruction manual User instructions, Cleaning The Filter Unit, Prolonged Disuse

Page 33
CLEANING THE FILTER UNIT

User instructions

CLEANING THE FILTER UNIT

It is advisable to periodically inspect the centre filter C and, if necessary, to clean it. To remove the filter, grip the tabs, turn them anticlockwise and lift upwards;

push the centre filter D from the underside to remove it from the micro-filter:

separate the two parts which make up the plastic filter by pressing the body of the filter in the zone shown by the arrows;

remove the centre filter by lifting it upwards.

GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE:

The filters should be cleaned under running water using a stiff brush.

When removing the filter, take care that there are no food residues on it. If any residues fall into the washing pit they might block hydraulic components, or foul the spray arm nozzles.

It is essential to thoroughly clean the filters according to the above instructions: the dishwasher cannot function if the filters are clogged.

Carefully replace the filters in their seats, to avoid damaging the wash pump.

PROLONGED DISUSE:

Run the soak program twice in succession.

Unplug the power cord from the socket.

Leave the door slightly open, in order to prevent the formation of unpleasant odours inside the washing tank.

Fill the rinse aid dispenser.

Shut off the water supply tap.

32

Image 33
Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. Safety and operating instructions Safety instructionsTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS Installation instructions 2. Installation and hook-upFor free-standing models only CONNECTING TO THE WATER SUPPLY 2.1 Water supply connectionDRAIN CONNECTION IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD 2.2 Electrical connection and precautionsFOR GREAT BRITAIN ONLY Fuse replacement3. Description of the controls User instructions7 START/STOP BUTTON 8 POWER ON LIGHT 3.1 Front panelLOAD CROCKERY PROGRAMME NUMBER & SYMBOLPROGRAM DURATIONBefore starting a washing program make sure that 3.3 Washing programsThe correct amount of detergent has been added to the dispenser LIGHTINGSTART PROGRAM SELECTION PROGRAMEND PROGRAM INTERRUPTING A PROGRAMSTOPPING A PROGRAM TO CHANGE A PROGRAMParticularly, on the display it will have the following indications HALF LOAD WASH FUNCTION on some models only TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTREMOVING THE DISHES 4.1 Using the water softening system 4. Operating instructionsUser instructions WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensersADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTINGDuring the washing cycle, the dispenser will be opened automatically ADDING THE DETERGENTUser instructions 4.3 General warnings and recommendations Correct loading of the dishes helps ensure optimal washing resultsMAKE SURE that the items being washed are dishwasher-safe Dishes and objects in copper, tin, zinc or brass these tend to stain Items which are not dishwasher-safe4.4 Using the baskets LOWER BASKETLOADING THE LOWER BASKET CUTLERY BASKET LOADING THE UPPER BASKET UPPER BASKETDepending on the models, the basket may be equipped with some or all of the following accessories Version B ADJUSTING THE UPPER BASKETUser instructions CLEANING THE WATER INTAKE FILTER 5. Cleaning and maintenanceCLEANING THE SPRAY ARMS 5.1 General warnings and recommendationsGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE CLEANING THE FILTER UNITPROLONGED DISUSE Fill the rinse aid dispenser Shut off the water supply tapIf the dishes are not being cleaned properly, check that TROUBLESHOOTING MINOR PROBLEMSBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE Reconnect the water intake hose and open the tap againIf the dishes fail to dry or remain dull, check that If the dishes show signs of streaking, staining, etc., check thatIf there are visible traces of rust inside the tank TABLE OF FAULTS DETECTED BY THE SELF-DIAGNOSTICS SYSTEM 6. TroubleshootingFAULT E1 E2 E3 E4 E5 E6 E7 E8 E9Electrical characteristics TECHNICAL DATAWidth Capacitydes ressortslateraux avant l’installation mollelaterali primadell’installazioneMontare la porta e regolarelatensione delle einstellen