Smeg DI612A1 User instructions, “3/1” OPTION BUTTON, “3/1” OPTION LIGHT, Half Load Button

Page 11

“3/1” OPTION BUTTON

User instructions

8

9

“3/1” OPTION BUTTON

Press this button to activate the option for use of 3/1 products.

“3/1” OPTION LIGHT

Illuminates to indicate that the function is activated.

10

HALF LOAD BUTTON

Press this button to activate the half load wash option.

HALF LOAD LIGHTS

11 One of the two light illuminates to indicate that the half load wash

12

option in the top or bottom basket has been selected.

PROGRAM DELAY BUTTON

Press this button to delay the start of the program by up to 9 hours.

13 INFORMATION DISPLAY

SETTING THE WASHING PROGRAM AND SWITCHING ON

To select the most suitable program for the dishes to be washed refer to the table below, which indicates the most appropriate program according to dish type and degree of soiling.

After using the table to identify the most appropriate washing program:

•press the ON/OFF button (1) and wait for the PROGRAM INDICATOR LIGHT (2) to illuminate;

•keep pressing the PROGRAM SELECTION button (3) until the indicator light corresponding to the desired program illuminates;

•close the door; after about 2" the program will start. While it is in progress, the relative LIGHT will flash (indicating that the program is being executed).

10

Image 11

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents NEVER BE REMOVED Safety instructions1. Safety and operating instructions USES OTHER THAN THOSE DESCRIBED ABOVETHIS DISHWASHER MUST BE USED BY ADULTS APPLIANCE AQUASTOP MODELSFor free-standing models only Installation instructions2. Installation and hook-up DRAIN CONNECTION CONNECTING TO THE WATER SUPPLY2.1 Water supply connection IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD 2.2 Electrical connection and precautionsNEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD FOR GREAT BRITAIN ONLY Fuse replacement3.1 Upper panel User instructions3. Description of the controls SELECTED PROGRAM INDICATOR LIGHTSHALF LOAD BUTTON 13 INFORMATION DISPLAY SETTING THE WASHING PROGRAM AND SWITCHING ON“3/1” OPTION BUTTON “3/1” OPTION LIGHTOnly run the soak program with half loads Very dirty pans QUICK TIME available in all programs except the soak program 3.2 Washing programsBefore starting a washing program make sure that The correct amount of detergent has been added to the dispenserTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT CANCELLING THE CURRENT PROGRAMDELAYED START available in all programs except the soak program CHANGING THE PROGRAMREMOVING THE DISHES TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTEND OF CYCLE 4.1 Using the water softening system 4. Operating instructionsADJUSTING THE WATER SOFTENING SYSTEM WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensersADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTINGDuring the washing cycle, the dispenser will be opened automatically ADDING THE DETERGENTUser instructions MAKE SURE that the items being washed are dishwasher-safe 4.3 General warnings and recommendationsCorrect loading of the dishes helps ensure optimal washing results Dishes and objects in copper, tin, zinc or brass these tend to stain Items which are not dishwasher-safeLOADING THE LOWER BASKET 4.4 Using the basketsLOWER BASKET UPPER BASKET CUTLERY BASKETLoading examples Models with cutlery racks LOADING THE UPPER BASKETVersion B ADJUSTING THE UPPER BASKETUser instructions 5.1 General warnings and recommendations 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER CLEANING THE SPRAY ARMSFill the rinse aid dispenser Shut off the water supply tap CLEANING THE FILTER UNITGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE PROLONGED DISUSEReconnect the water intake hose and open the tap again TROUBLESHOOTING MINOR PROBLEMSIf the dishes are not being cleaned properly, check that BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSEIf there are visible traces of rust inside the tank If the dishes fail to dry or remain dull, check thatIf the dishes show signs of streaking, staining, etc., check that E1 E2 E3 E4 E5 E6 6. TroubleshootingFAULT Safety levelWater intake system malfunction E7 E8 E9Turbine flow-regulator malfunction Alternate washing system malfunctionWidth Depth Height depending on models Capacity Water supply pressure TECHNICAL DATAElectrical characteristics