Whirlpool W10403811C installation instructions Tools and Parts, Location Requirements

Page 3

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■

Tape measure

■

Masking tape

■

Flat-blade screwdriver

■

¼" drive ratchet

■

Phillips screwdriver

■

¼" nut driver

■

Level

■

³⁄₈" and ⁵⁄₁₆" nut driver

■

Hammer

■ ¹⁄₈" (3.2 mm) drill bit (for

■ Hand or electric drill

 

wood floors)

■ Tin snips or large wire

■

Wrench or pliers

 

cutters (for cutting ground

 

 

 

■

Marker or pencil

 

strap if necessary)

Parts supplied

Check that all parts are included.

■3 - 10-32 hex nuts (attached to terminal block)

■3 - Terminal lugs

A

B

A.Anti-tip bracket

B.#12 x 1⁵⁄₈" screws (2)

■Anti-tip bracket must be securely mounted to floor or wall. Thickness of flooring may require longer screws to anchor bracket to floor.

Parts needed

If using a power supply cord kit:

■A UL listed power supply cord kit marked for use with ranges. The cord should be rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

■A UL listed strain relief.

Check local codes. Check existing electrical supply. See the appropriate “Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the frame behind a top corner of the door or either side of the drawer.

■To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

■The anti-tip bracket must be installed. To install the anti-tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

■Grounded electrical supply is required. See the appropriate “Electrical Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194° (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be secured per the instructions in this document.

■Four-wire power supply cord or cable must be used in a mobile home installation. The appliance wiring will need to be revised. See “Electrical Connection - U.S.A. Only” section.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Table of Contents Range Safety Location Requirements Tools and PartsProduct Dimensions Cabinet Dimensions Electrical Connection If connecting to a 4-wire systemIf connecting to a 3-wire system Electrical Requirements U.S.A. OnlyInstall Anti-Tip Bracket Unpack RangeOn Ranges Equipped with a Storage Drawer Wall Mounting Floor MountingPower Supply Cord Direct Wire Style 1 Power supply cord strain reliefElectrical Connection U.S.A. Only Wire connection Power Supply Cord Style 2 Direct wire strain reliefIf your home has You will be Go to Section Connecting to Wire Connection Direct Wire Direct Wire Installation Copper or Aluminum WireWire Awg Torque Bare Wire Torque SpecificationsGauge copper Lbs-in .8 N-m Gauge aluminum Lbs-in .0 N-m Verify Anti-Tip Bracket Is Installed EngagedTo Replace Level RangeWarming Drawer or Premium Storage To RemoveIf range does not operate, check the following Complete InstallationStorage Drawer Oven DoorFor direct-wired ranges For power supply cord-connected rangesMoving the Range W10403811C

W10403811C specifications

The Whirlpool W10403811C is a versatile and essential component for modern kitchens, serving as a range hood that enhances both functionality and aesthetic appeal. This powerful appliance is designed to improve ventilation, ensuring a clean and comfortable cooking environment by efficiently removing smoke, grease, and odors from the air.

One of the standout features of the W10403811C is its robust motor, which offers multiple fan speeds. This flexibility allows users to adjust the airflow based on their cooking needs, whether they’re simmering a delicate sauce or searing meats. The strong performance minimizes the accumulation of cooking residues on surfaces, making it easier to maintain a clean kitchen.

The design of the W10403811C is not only stylish but also practical. Its sleek stainless steel finish complements a variety of kitchen decors, providing a modern look that many homeowners desire. Additionally, the range hood includes integrated LED lighting, which adds brightness to the cooking space while also enhancing visibility when preparing meals. The energy-efficient LED bulbs last longer than traditional bulbs, reducing the need for frequent replacements.

In terms of installation, the W10403811C offers flexibility with both ducted and ductless options, catering to different kitchen layouts and preferences. For ductless installations, the appliance can be equipped with a charcoal filter that effectively recirculates the air, making it suitable for spaces without external ventilation.

Another impressive characteristic of this range hood is its quiet operation. Unlike some models that can be disruptive during cooking, the Whirlpool W10403811C is engineered to minimize noise, allowing for pleasant and uninterrupted cooking and dining experiences. This feature is especially valued in open-plan living areas where the kitchen, dining, and living spaces are interconnected.

Lastly, maintenance of the W10403811C is made easy with its dishwasher-safe filters. Regular cleaning of the filters is crucial for maintaining peak performance and extending the lifespan of the appliance. This user-friendly approach to maintenance empowers homeowners to keep their range hood operating at optimal efficiency without significant effort.

Overall, the Whirlpool W10403811C excels in delivering essential features, advanced technology, and thoughtful design, making it a valuable addition to any modern kitchen. Its combination of efficient ventilation, attractive aesthetics, and ease of use ensures that culinary enthusiasts can create delicious meals in a clean and comfortable environment.
Top Page Image Contents