Caring For Your Range
Solid element surface units (Model FES375V)
Burn And Electrical Shock Hazard |
| |
Make sure all controls are OFF and |
| |
the range is cool before cleaning |
|
|
Failure to do so can result in burns |
| |
1 or electrical shock. | ’ | 1 |
The control knobs
1.Turn control knobs to the OFF position.
2.Pull control knobs and command buttons straight off.
3.Wash in warm, soapy water.
4.Rinse well and dry completely. Do not soak.
The control panel
1.Wipe with warm, soapy water or spray glass cleaner, and a soft cloth.
2.Rinse well.
3.Dry with soft cloth.
4.Replace control knobs and command buttons by pushing them firmly into place.
NOTE: When cleaning, never use steel wool, abrasives, or commercial oven cleaners which may damage the finish. After cleaning, make sure all control knobs point to the OFF position, Make sure you have not turned oven ON when replacing buttons. If oven has been turned on, push Set/Cancel button.
Surface units and reflector bowls (all models except FES375V)
Removing
3.Pull the surface unit straight away from the receptacle.
4.Lift out the reflector bowl. See Cleaning Chart on page 12 for cleaning instructions.
Replacing
1.Make sure all surface units are turned OFF.
2.Line up openings in the reflector bowl with the surface unit receptacle.
3.Hold the surface unit as level as possible with the terminal just started into the receptacle. Push the surface unit terminal into the receptacle.
4.When the terminal is pushed into the receptacle as far as it will go, the surface unit will fit into the reflector bowl.
Reflector bowls reflect heat back to the utensils on the surface units. They also help catch spills. When they are kept clean, they reflect heat better and look new longer.
If a reflector bowl gets discolored, some of the utensils may not be flat enough, or some may be too large for the surface unit. In either case, some of the heat that’s meant to go into or around a utensil goes down and heats the reflector bowl. This extra heat can discolor it.
1. For best results, wipe off surface | |||
units with a damp soft cloth and | |||
soapy water after each use. Remove | |||
scouring pad. The red spot in the | |||
center of the surface unit will | |||
gradually wash off. This is normal | |||
and will not affect the operation of | |||
the surface unit. |
| ||
IMPORTANT: | Dry the element | ||
completely after cleaning. Turn on | |||
the element for a few minutes to | |||
thoroughly dry. After the element | |||
has cooled, use a paper towel to | |||
apply a thin coat of | |||
the surface units to season and | |||
restore the finish. Wipe excess oil off | |||
stainless steel trim rings. Then heat | |||
3 - 5 minutes. Some smoking may | |||
occur; this is normal. If surface units | |||
have dark spots caused by grease | |||
and food, the oil treatment will | |||
improve their appearance but not | |||
eliminate | the | spots. | |
NOTE: Optional | Electrol” dressing | ||
can be applied to the surface units | |||
to improve | their | appearance. | |
The stainless steel trim rings will | |||
yellow from the heat of the surface | |||
units and pans. This is normal. The | |||
yellowing can be removed by using | |||
stainless steel cleaner or Cook Top | |||
Polishing Creme on the trim rings. | |||
To obtain order information for Cook | |||
Top Polishing Creme (Part No. | |||
Fire And Electrical Shock Hazard
Do not line the reflector bowls with
1.Turn off all surface units and let cool.
2.Lift the edge of the unit opposite the receptacle, just enough to clear the reflector bowl.
814009) or Electrole dressing (Part | |
No. 814030), write to: | |
Whirlpool | Corporation |
Attention: | Customer Service Dept. |
1900 Whirlpool Drive | |
LaPorte. IN 46305 | |
Page 9