Whirlpool GXW7230DAS Installation Requirements, ToolsandParts, LocationRequirements

Page 4

INSTALLATION REQUIREMENTS

ToolsandParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Level

Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), and ³⁄₁₆" (4.8 mm) drill bits

Pencil

Wire stripper or utility knife

Tape measure or ruler

Pliers

Caulking gun and weatherproof caulking compound

Vent clamps

Jigsaw or keyhole saw

Flat-blade screwdriver

Metal snips

Phillips screwdriver

Parts needed

Home power supply cable

½" (12.7 mm) UL listed or CSA approved strain relief

3 UL listed wire connectors

For vented installations, you will also need:

1 wall or roof cap

LocationRequirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the filter on the rear wall of the vent hood.

Canopy hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements” section.

The canopy hood is factory set for venting through the roof or wall. For non-vented (recirculating) Installation see “For Non- vented (recirculating) Installations Only” in “Connect Vent System” section. Recirculation Kit Part Number W10349327 is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

Metal vent system

For non-vented (recirculating) installations, you will also need:

Recirculation Kit Part Number W10349327 for non-vented (recirculating) installations only. See “Assistance or Service” section to order.

6" (15.2 cm) dia. round metal vent duct - length required is determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

Hood canopy assembly with ventilator and light bulbs

 

installed

Vent transition with back draft dampers installed

Metal grease filter(s)

Vent cover support bracket

Mounting template

2-piece vent cover

2 - 3.5 x 9.5 mm screws

7¹⁄₄"

(18.4 cm)

30" (76.2 cm)

8¹⁄₈"

(20.7 cm)

*28⁷⁄₈" (73.3 cm) min.

42¹⁄₁₆" (106.9 cm) max.

**28³⁄₈" (72.0 cm) min. 38" (96.6 cm) max.

14¹⁄₈"

(35.9 cm)

10" (25.4 cm)

20" (50.8 cm)

1¹ " (4.0 cm)

4

- 2.9 x 6.5 mm screws

6

- 5 x

45 mm mounting screws

2

- 8 x

40 mm wall anchors

4

- 10 x 50 mm wall anchors

T10 Torx®adapter

®†TORX is a registered trademark of Saturn Fasteners, Inc.

*For non-vented (recirculating) installations

**For vented installations

4

Image 4
Contents Montage Mural 30 76,2 CM Range Hood Safety Table of ContentsImportant Safety Instructions ToolsandParts Installation RequirementsLocationRequirements VentingRequirements For Non-Vented recirculating Installations Electrical RequirementsCalculating Vent System Length Example vent systemInstallation Instructions Range Hood Mounting Screws InstallationVent Cover Support Bracket Installation PrepareLocationInstall RangeHood For vented installations onlyFor non-vented recirculating installation only ConnectVentSystemCompleteInstallation InstallVentCoversMakeElectrical Connection Cleaning Range Hood USERange Hood Care RangeHoodControlsReplacing the Incandescent Bulb Wiring Diagram SE12DAAssistance or Service AccessoriesIntheU.S.A InCanadaWhirlpool Corporation Major Appliance Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences d’emplacement Exigences DinstallationOutils etpièces Dimensions du placard Dimensions du produitExigencesconcernantl’évacuation Installation dans une région à climat froid Installations sans décharge à lextérieur recyclageAir dappoint Méthodes d’évacuationInstructions Dinstallation PréparationdelemplacementInstallation des vis de montage de la hotte SpécificationsélectriquesInstallationdelahotte Installation de la bride de cache-conduitRaccordementducircuitdévacuation Achever la préparationRaccordementélectrique Installationdes cache-conduits Acheverl’installationCommandesdelahottedecuisinière Utilisation DE LA HotteEntretien DE LA Hotte NettoyageRemplacement de la lampe à incandescence Filtres dinstallation sans décharge à l’extérieur recyclageRemplacement du filtre à charbon Schéma DE Câblage Assistance OU Service AccessoiresGarantie DES Gros Appareils Ménagers Whirlpool Corporation AuCanadaW10458667A

GXW7230DAS specifications

The Whirlpool GXW7230DAS is a powerful and efficient range hood designed to enhance your kitchen environment while providing exceptional performance and contemporary style. With an array of features and advanced technologies, it seamlessly blends functionality with aesthetic appeal.

One of the main features of the GXW7230DAS is its powerful ventilation system. Equipped with an internal blower, this range hood can deliver up to 400 CFM (cubic feet per minute) of airflow, effectively removing smoke, steam, and odors from your kitchen. This high airflow capability is particularly beneficial for kitchens that frequently engage in heavy cooking, ensuring a cleaner and more comfortable space.

The range hood offers a sleek design, available in stainless steel, which not only complements modern kitchen designs but also provides durability and ease of cleaning. The smooth surface helps resist fingerprints, making maintenance a breeze. Additionally, its under-cabinet installation saves space while positioning the unit conveniently above your cooking area.

Another remarkable characteristic of the GXW7230DAS is its variable speed fan control. Home cooks can choose from multiple fan speeds, allowing them to customize the ventilation based on the level of cooking activity. For light cooking, a lower setting suffices, while heavy-duty cooking can utilize the higher speeds for maximum efficiency.

The integrated LED lighting is another highlight of this model, providing bright illumination over the cooking surface. The energy-efficient bulbs enhance visibility while cooking and lend a modern touch to your kitchen ambiance. With a simple switch, users can control the lighting independently of the fan, promoting both convenience and efficiency.

One of the standout technologies in the GXW7230DAS is the dishwasher-safe grease filters. These filters effectively capture grease and particulate matter, protecting the internal components of the hood. Their removable design and compatibility with dishwashers simplify maintenance and ensure optimal performance over time.

In terms of noise levels, this range hood operates quietly, especially at lower speeds, promoting a more enjoyable cooking experience without excessive disruption. Overall, the Whirlpool GXW7230DAS is a blend of design, performance, and convenience, making it an excellent choice for homeowners seeking to elevate their kitchen’s functionality while maintaining an attractive appearance.