Installation Instructions Introduction

Installation Instructions

Introduction

Step 4: Check edging strip

The edging strip is factory fitted to the front side edges of the appliance front frame. This strip provides the cabinetry with extra protection from any escape of heat.

When installing the product, ensure that the edging strip is correctly located on the outer edges of the front frame, before positioning and securing the appliance to the cabinet.

seal	front frame

handle door

When securing the appliance, the fixing screws provided are driven through the edging strips into the cabinet - the seal will straighten up and sit flush to the cabinet when the screws are fully home.

Step 5: Secure appliance into housing unit

There are 4 black no 8 x 25mm long chipboard screws for securing appliance to cabinet.

Insert appliance into cabinet and secure - open the oven door and screw the 4 screws through the holes in the front frame.

Note: The unit housing the appliance must be appropriately fixed.

The cooling fan

The cooling fan helps to keep the exterior cool during normal use. When a burner is operated, you should hear the cooling fan switch on automatically and be able to feel air evacuating from the appliance vents just below the fascia. The cooling fan will continue to operate for approximately 10 minutes after turning off the burners. This is normal.

If there is no such indication that the fan is operating, the appliance will require servicing. DO NOT USE THE APPLIANCE UNTIL IT HAS BEEN SERVICED. Switch the appliance off at the mains and contact Customer Support.

For your safety

This appliance has a built in safety device to isolate the gas and electric supplies to various components in the event of fan failure.

If the minute minder and lights do not function, and the ignition system stops working, the safety device has operated. Within an hour the safety device will reset itself and the minute minder display will flash.

To reset the minute minder, simply press the reset button and set the time of day within 5 seconds by pressing the “+” plus and “-” minus buttons.

If when a burner control is turned on, the fan does not operate in the normal way, then the appliance will require

servicing. DO NOT USE THE APPLIANCE UNTIL IT HAS BEEN SERVICED. Switch the appliance off at the mains and contact Customer Support.

Continued use of the appliance without it being serviced could result in

excessive temperatures being generated, which in turn could reduce the life of certain components.

Ventilation

The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Ensure that the kitchen is well ventilated; keep natural ventilation holes open or install a mechanical ventilation device (mechanical ventilator).

Prolonged intensive use of the appliance may call for additional ventilation, for example opening a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present.

This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention must be given to the relevant regulations regarding ventilation.

SO11GB, SO11GW specifications

The Creda SO11GW and SO11GB are two compact and efficient electric storage heaters designed to provide warmth and comfort in residential and commercial spaces. Both models showcase modern technology and user-friendly features that make them a popular choice for those looking to optimize their heating solutions.

One of the standout features of the Creda SO11GW and SO11GB is their advanced thermal storage system. These heaters store heat during off-peak electricity hours, making them cost-effective and energy-efficient. By utilizing lower energy tariffs, users can significantly reduce their heating bills, particularly during colder months when heating demands rise.

The Creda SO11GW, with its white finish, is designed to seamlessly blend into various interior styles, while the SO11GB, in a graphite finish, offers a sleek, contemporary alternative. Both models are compact in design, allowing for easy installation in small spaces, such as apartments or rooms where floor area is a consideration.

In terms of control and functionality, these heaters are equipped with an electronic timer and programmable controls. This technology allows users to set specific heating schedules, ensuring the space is warm when needed without unnecessary heat loss. The intuitive interface makes it easy to adjust settings and monitor energy usage, promoting user engagement with their heating solution.

Another essential characteristic of the Creda SO11GW and SO11GB is the built-in safety features. These models incorporate overheat protection and a thermal cut-out mechanism to prevent overheating, providing peace of mind for users. The heaters also feature an insulated body, ensuring that surfaces do not become dangerously hot to the touch, which is particularly important in homes with children or pets.

The heaters also come with a robust and durable construction, designed to withstand the rigors of daily use. With their long-lasting ceramic bricks, which retain and release heat evenly, the Creda SO11GW and SO11GB ensure consistent warmth throughout the heating period.

In summary, the Creda SO11GW and SO11GB are efficient, stylish electric storage heaters that combine modern aesthetics with practical technology. Their ability to deliver controlled and cost-effective heating makes them an attractive option for anyone seeking reliable warmth in their living spaces. With advanced features, user-friendly controls, and enhanced safety mechanisms, these models are well-suited to meet the diverse heating needs of today's consumers.