Using the Grill

Installation Instructions
Step 1: Prepare installation	90	mm
	90		(minimum)
door handle.			(minimum)
Do not lift the appliance by the

Using the grill

Push the grill pan towards the back of the shelf, to position it under the grill.

Whilst every care is taken to eliminate burrs and raw edges from this product, please take care when handling - we recommend the use of protective gloves during installation.

Please note that the weight of this appliance is approximately 31kg (unpacked). Take care when lifting it into the housing unit - always use an appropriate method of lifting.

Remove the fixing screws from the polythene bag on the top of the appliance, but leave the appliance in the base tray packaging until you are ready to install it.

If this appliance is to be installed near to a corner where the adjacent cabinets run at right angles forward of the appliance, there must be a gap of at least 90 mm between the appliance and the cabinets, to prevent overheating of the cabinets.

Housing dimensions

The appliance is designed to fit into a standard 600mm wide housing unit with minimum internal dimensions as shown.

591mm is to the underside of the worktop when the appliance is built under, or to the underside of the panel above, when the appliance is installed into a tall housing unit.

min 560mm

Variation in grilling can be achieved by setting the grill between the large and small flame symbols, or by moving the grill pan up or down. Important: Never operate the grill between the large flame and the off position.

The speed of grilling can also be controlled by selecting a higher or lower shelf position.

Always use the top shelf position for fast toasting.

For toasting, and for grilling foods such as bacon, sausages or steaks, use a higher shelf position.

For thicker foods such as chops or chicken joint pieces, use a middle to low shelf position.

The grill trivet, inside the grill pan, can be inverted to give a high or low position, or it may be removed.

When you have finished grilling,

585

595mm

547mm	min			- 80mm
20mm			550mm
20mm			30
			30
588	12mm	gap
588

mm	568		in	plinth
	568			plinth
	mm
550mm

min	min
580	590
mm	mm

6mm

check that the control knob is returned to the off position.

SO11GB, SO11GW specifications

The Creda SO11GW and SO11GB are two compact and efficient electric storage heaters designed to provide warmth and comfort in residential and commercial spaces. Both models showcase modern technology and user-friendly features that make them a popular choice for those looking to optimize their heating solutions.

One of the standout features of the Creda SO11GW and SO11GB is their advanced thermal storage system. These heaters store heat during off-peak electricity hours, making them cost-effective and energy-efficient. By utilizing lower energy tariffs, users can significantly reduce their heating bills, particularly during colder months when heating demands rise.

The Creda SO11GW, with its white finish, is designed to seamlessly blend into various interior styles, while the SO11GB, in a graphite finish, offers a sleek, contemporary alternative. Both models are compact in design, allowing for easy installation in small spaces, such as apartments or rooms where floor area is a consideration.

In terms of control and functionality, these heaters are equipped with an electronic timer and programmable controls. This technology allows users to set specific heating schedules, ensuring the space is warm when needed without unnecessary heat loss. The intuitive interface makes it easy to adjust settings and monitor energy usage, promoting user engagement with their heating solution.

Another essential characteristic of the Creda SO11GW and SO11GB is the built-in safety features. These models incorporate overheat protection and a thermal cut-out mechanism to prevent overheating, providing peace of mind for users. The heaters also feature an insulated body, ensuring that surfaces do not become dangerously hot to the touch, which is particularly important in homes with children or pets.

The heaters also come with a robust and durable construction, designed to withstand the rigors of daily use. With their long-lasting ceramic bricks, which retain and release heat evenly, the Creda SO11GW and SO11GB ensure consistent warmth throughout the heating period.

In summary, the Creda SO11GW and SO11GB are efficient, stylish electric storage heaters that combine modern aesthetics with practical technology. Their ability to deliver controlled and cost-effective heating makes them an attractive option for anyone seeking reliable warmth in their living spaces. With advanced features, user-friendly controls, and enhanced safety mechanisms, these models are well-suited to meet the diverse heating needs of today's consumers.