Using the Grill Installation Instructions

Using the Grill

Installation Instructions

Caution: Accessible parts may be hot when the grill is used, young children should be kept away.

Grill ignition

Important: The door must be fully open when the grill is used.

Open the door.

Detachable grill pan handle

trivet

i)When installed in a typical 600mm deep built in housing unit, the false back should be removed from the housing unit to provide the necessary depth for installation.

ii)When the false back is removed, it is normally the case that the support shelf for the appliance leaves a gap between the back edge and the wall of approximately 80mm.

Important: Do not modify the outer panels of this appliance in any way.

Ensure that you route all mains electrical cables and flexible tubing well clear of any adjacent heat source, such as an oven, grill or hob.

Ensure that all pipe work is of the correct rating for both size and temperature.

Push in and turn the grill control knob clockwise to the “on” position. Ensure that the grill burner is alight before leaving it unattended.

Do not operate the grill between the “on” setting and the “off” position - use the “on” setting only.

To switch off, turn the control knob anti-clockwise to return it to the “●” off position.

If for any reason the burner does not light within 15 seconds turn the control off and wait for one minute before beginning a further ignition attempt.

grill pan

handle handle position indicators

Place the handle over the edge of the grill pan, at the narrow side edges. Slide the handle to the centre, and locate between the handle position indicators.

iii)If no gap occurs between the back edge of the shelf and the wall behind the unit, we recommend that a gap of at least 30mm is made by shortening the shelf.

iv)When installing the appliance below a worktop, there must be a minimum ventilation area of 60cm2 below the appliance, in either area (1) or (2), as indicated below. There must be a 5mm gap between the front top edge of the oven and the underside of the worktop.

5 mm

Installing the appliance under a worktop

Where the appliance is installed under a worktop, with a hob installed above it, the installation instructions for the hob must be read in conjunction with these instructions.

worktop

Aluminium foil

Never cover the grill pan or grill trivet with cooking foil, or allow fat to build up in the grill pan, as this creates a fire hazard.

The handle should be removed from the pan during grilling, to prevent overheating.

The handle is designed for removing / inserting the grill pan under the grill when grilling.

If cleaning the grill pan when it is hot, use oven gloves to move it. Do not use the handle to pour hot fats from the grill pan.

Food for grilling should be positioned centrally on the trivet.

front

wall

of oven

rear

(1)

minimum

support shelf

30 - 80

ventilation

area 60 cm2

(2)

SO11GB, SO11GW specifications

The Creda SO11GW and SO11GB are two compact and efficient electric storage heaters designed to provide warmth and comfort in residential and commercial spaces. Both models showcase modern technology and user-friendly features that make them a popular choice for those looking to optimize their heating solutions.

One of the standout features of the Creda SO11GW and SO11GB is their advanced thermal storage system. These heaters store heat during off-peak electricity hours, making them cost-effective and energy-efficient. By utilizing lower energy tariffs, users can significantly reduce their heating bills, particularly during colder months when heating demands rise.

The Creda SO11GW, with its white finish, is designed to seamlessly blend into various interior styles, while the SO11GB, in a graphite finish, offers a sleek, contemporary alternative. Both models are compact in design, allowing for easy installation in small spaces, such as apartments or rooms where floor area is a consideration.

In terms of control and functionality, these heaters are equipped with an electronic timer and programmable controls. This technology allows users to set specific heating schedules, ensuring the space is warm when needed without unnecessary heat loss. The intuitive interface makes it easy to adjust settings and monitor energy usage, promoting user engagement with their heating solution.

Another essential characteristic of the Creda SO11GW and SO11GB is the built-in safety features. These models incorporate overheat protection and a thermal cut-out mechanism to prevent overheating, providing peace of mind for users. The heaters also feature an insulated body, ensuring that surfaces do not become dangerously hot to the touch, which is particularly important in homes with children or pets.

The heaters also come with a robust and durable construction, designed to withstand the rigors of daily use. With their long-lasting ceramic bricks, which retain and release heat evenly, the Creda SO11GW and SO11GB ensure consistent warmth throughout the heating period.

In summary, the Creda SO11GW and SO11GB are efficient, stylish electric storage heaters that combine modern aesthetics with practical technology. Their ability to deliver controlled and cost-effective heating makes them an attractive option for anyone seeking reliable warmth in their living spaces. With advanced features, user-friendly controls, and enhanced safety mechanisms, these models are well-suited to meet the diverse heating needs of today's consumers.