Continental Refrigerator Refrigerators and Freezers Removal of Doors and Door Adjustment

Page 10

FIGURE 4

CONDENSATE EVAPORATOR INSTALLATION

REMOVAL OF DOORS AND DOOR ADJUSTMENT

During installation, it may become necessary to remove the cabinet doors to facilitate passage through narrow doorways or hallways. To remove a door, pry off all hinge covers using a sharp tool or knife (see figure 5). Swing the door to the open-door position (90 degrees) and carefully lift the door upward, removing the door from the hinge bodies. If it is necessary to remove the hinge bodies from the cabinet face, be extremely careful not to lose the light switch pin located inside all top hinge bodies. To reinstall the door, reverse the above procedure.

All doors have been aligned at the factory, however vibration during transportation may cause doors to shift and realignment may be necessary. If the door(s)

require realignment, proceed as follows:

1.Pry off all hinge covers using a sharp tool or knife.

2.For each door, loosen the screws which secure the hinge bodies to the cabinet face and slide the door into alignment. Hold the door firmly in place and tighten all screws securely.

If the door gasket(s) do not seal properly to the cabinet face and there are gaps between the gasket and the face on the hinge edge, proceed as follows:

1.For each door, loosen all screws which are directed into the edge of the door and push the door towards the cabinet eliminating the gap. Hold the door firmly in place and tighten all screws securely.

2.Replace all snap-on hinge covers.

- 7 -

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Reach-In Refrigerators and Freezers Operators Manual Table of Contents Troubleshooting and Servicing Guide Wiring Diagrams Receiving Your NEW Model General Information and Important Operating FactsUncrating Your NEW Model Installation and Location ClearancesVentilation Floor Loads Installing Legs and Leveling REACH-IN Models Mounting ROLL-IN Models in Place and LevelingInstalling Casters and Leveling REACH-IN Models Installing Condensate Evaporator Removal of Doors and Door Adjustment Require realignment, proceed as followsInitial Cleaning Procedure Removal of GrillSTART-UP Procedure Electrical Connections VOLT, 60 HZ, 1 Phase ConnectionSpecial Voltage Connections START-UP ChecklistRemote Applications Calibration Check OperationThermometer Calibration Dial ThermometerDigital Thermometer Refrigerator System and Adjustment Freezer System and Adjustment Defrost Operation Evaporator Assembly LOW-PROFILE, CEILING-MOUNT Evaporator AssemblyInterior REACH-IN Accessories Shelving InstallationOptional Interior Accessories Safety Precautions Maintenance Periodic Cleaning Procedure PrecautionsGeneral Preventative Maintenance Sliding and Hinged GlassParts and Service Model # Serial # Troubleshooting and Servicing GuideProblem Probable Cause Correction Not start no humCondensing unit runs Product zone Wiring Diagrams Page Page Page Page Page

Refrigerators and Freezers specifications

Continental Refrigerator is a leader in the manufacturing and design of high-quality commercial refrigerators and freezers. Renowned for their durability and reliability, Continental Refrigerators are a staple in restaurants, grocery stores, and other commercial food service establishments.

One of the standout features of Continental Refrigerators is their robust construction. Built with stainless steel and corrosion-resistant materials, these units are designed to withstand the rigors of a busy kitchen. The exterior is sleek and easy to clean, while the interior is designed for efficiency and organization, often featuring adjustable shelves and easy-access compartments.

In terms of technology, Continental Refrigerators utilize state-of-the-art refrigeration systems that ensure precise temperature control. With digital temperature displays and intuitive controls, users can easily monitor and adjust settings to meet specific storage needs. Many models come equipped with energy-efficient compressors and eco-friendly refrigerants, aligning with modern sustainability practices without sacrificing performance.

The cooling technology employed in Continental Refrigerators ensures rapid temperature recovery after door openings, which is critical for maintaining food safety standards. The units are designed with powerful fans that promote optimal air circulation, helping to ensure uniform temperatures throughout the interior.

Another significant characteristic is the noise reduction technology implemented in many Continental models. These refrigerators are engineered to operate quietly, contributing to a more pleasant working environment.

Additionally, Continental Refrigerators are built for versatility. They offer a range of options, from undercounter models to walk-in coolers, catering to various business sizes and needs. The ability to customize configurations ensures that businesses can maximize space while still maintaining access to essential refrigerated items.

Lastly, the brand is recognized for its customer support and warranty options, providing peace of mind for operators. Overall, Continental Refrigerators and Freezers combine durability, efficiency, and cutting-edge technology, making them an excellent choice for any commercial kitchen looking to maintain food safety and quality.
Top Page Image Contents