Continental Refrigerator Refrigerators and Freezers Installing Legs and Leveling REACH-IN Models

Page 7

approximately 700 pounds of product (35 x 20) and assuming the refrigerator itself weighs 300 pounds, the total combined weight of cabinet and product is approximately 1000 pounds. Therefore, the floor in this example must be capable of supporting up to 1000 pounds.

INSTALLING LEGS AND LEVELING REACH-IN MODELS

Your new reach-in model is supplied with adjustable type legs for leveling purposes. Each single and two section model has four leg mounting holes on its case bottom, and three section models have six leg mounting holes. Legs are packed in the accessory carton from which they must be removed and installed on the cabinet case bottom (see figure 2). In order to install the legs, carefully tip the cabinet rearward adding four (4) 2" wood blocks underneath and simply screw the threaded leg studs into the case bottom front leg holes. Repeat this procedure by tilting the cabinet in the opposite direction and install the remaining legs. Make sure the legs are tightened extremely well or the entire model will sway or rock with each opening or closing of the doors, possibly causing damage to the case bottom. This procedure should be performed close to the final installation site and allow access to the rear of the cabinet for condensate evaporator installation (see "condensate evaporator installation" under installation and location section).

To assure your cabinet is level, all legs are equipped with bullet-type leveling bolts. These bolts can be turned by hand or by wrench, clockwise or counterclockwise to level the cabinet.

FIGURE 2

LEG INSTALLATION

MOUNTING ROLL-IN MODELS IN PLACE AND LEVELING

Your new roll-in model is designed and constructed to be mounted directly on the floor without legs or casters. The floor must be level and the base of the cabinet should be sealed to the floor around its entire perimeter. If the floor is not level, it must be made level prior to mounting your roll-in model.

- 4 -

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Reach-In Refrigerators and Freezers Operators Manual Table of Contents Troubleshooting and Servicing Guide Wiring Diagrams General Information and Important Operating Facts Receiving Your NEW ModelUncrating Your NEW Model Installation and Location ClearancesVentilation Floor Loads Mounting ROLL-IN Models in Place and Leveling Installing Legs and Leveling REACH-IN ModelsInstalling Casters and Leveling REACH-IN Models Installing Condensate Evaporator Require realignment, proceed as follows Removal of Doors and Door AdjustmentRemoval of Grill Initial Cleaning ProcedureVOLT, 60 HZ, 1 Phase Connection START-UP Procedure Electrical ConnectionsSpecial Voltage Connections START-UP ChecklistRemote Applications Dial Thermometer OperationThermometer Calibration Calibration CheckDigital Thermometer Refrigerator System and Adjustment Freezer System and Adjustment Defrost Operation LOW-PROFILE, CEILING-MOUNT Evaporator Assembly Evaporator AssemblyShelving Installation Interior REACH-IN AccessoriesOptional Interior Accessories Safety Precautions Precautions Maintenance Periodic Cleaning ProcedureSliding and Hinged Glass General Preventative MaintenanceModel # Serial # Troubleshooting and Servicing Guide Parts and ServiceNot start no hum Problem Probable Cause CorrectionCondensing unit runs Product zone Wiring Diagrams Page Page Page Page Page

Refrigerators and Freezers specifications

Continental Refrigerator is a leader in the manufacturing and design of high-quality commercial refrigerators and freezers. Renowned for their durability and reliability, Continental Refrigerators are a staple in restaurants, grocery stores, and other commercial food service establishments.

One of the standout features of Continental Refrigerators is their robust construction. Built with stainless steel and corrosion-resistant materials, these units are designed to withstand the rigors of a busy kitchen. The exterior is sleek and easy to clean, while the interior is designed for efficiency and organization, often featuring adjustable shelves and easy-access compartments.

In terms of technology, Continental Refrigerators utilize state-of-the-art refrigeration systems that ensure precise temperature control. With digital temperature displays and intuitive controls, users can easily monitor and adjust settings to meet specific storage needs. Many models come equipped with energy-efficient compressors and eco-friendly refrigerants, aligning with modern sustainability practices without sacrificing performance.

The cooling technology employed in Continental Refrigerators ensures rapid temperature recovery after door openings, which is critical for maintaining food safety standards. The units are designed with powerful fans that promote optimal air circulation, helping to ensure uniform temperatures throughout the interior.

Another significant characteristic is the noise reduction technology implemented in many Continental models. These refrigerators are engineered to operate quietly, contributing to a more pleasant working environment.

Additionally, Continental Refrigerators are built for versatility. They offer a range of options, from undercounter models to walk-in coolers, catering to various business sizes and needs. The ability to customize configurations ensures that businesses can maximize space while still maintaining access to essential refrigerated items.

Lastly, the brand is recognized for its customer support and warranty options, providing peace of mind for operators. Overall, Continental Refrigerators and Freezers combine durability, efficiency, and cutting-edge technology, making them an excellent choice for any commercial kitchen looking to maintain food safety and quality.
Top Page Image Contents