Whirlpool W10215185A Crisper Humidity Control, Ice Maker and Ice Storage Bin

Page 10

To Access the User Preferences Menu:

1.Press and hold the Door Alarm touch pad for three seconds. The preference name will appear in the Freezer display and the preference status (F or C) or (ON or OFF) will appear in the Refrigerator display.

2.Use the Freezer (+) or (-) touch pads to scroll through the preference names. When the desired preference name is displayed, press the Refrigerator (+) or (-) touch pads to change the preference status.

3.Set your preferences by pressing and holding the Door Alarm touch pad for three seconds.

Crisper Humidity Control

You can control the amount of humidity in the moisture-sealed crisper. Depending on your model, adjust the control to any setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT / LOW (open) for best storage of fruits and vegetables with skins.

VEGETABLES / HIGH (closed) for best storage of fresh, leafy vegetables.

Ice Maker and Ice Storage Bin

The ice maker and storage bin are located in the upper left-hand side of the refrigerator compartment.

Turning the Ice Maker On/Off

The On/Off switch is located on the ice maker.

To turn on the ice maker, press the switch to the ON position.

To manually turn off the ice maker, press the switch to the OFF position.

NOTE: Your ice maker has an automatic shutoff. The ice maker sensors will automatically stop ice production, but the control will remain in the ON position.

Removing and Replacing Ice Storage Bin

To Remove the Ice Storage Bin:

1.Hold the base of the storage bin and press the release button on the lower right.

2.Pull the storage bin out until resistance is felt. Lift up the front of the ice bin and remove.

3.Press the switch to the OFF position

To Replace the Ice Storage Bin:

IMPORTANT: It may be necessary to turn the auger driver, behind the ice bin, counterclockwise to properly align the ice bin with the auger driver. The ice storage bin must be locked in place for proper ice dispensing.

1.Press the switch to the ON position

2.Slide the ice bin into the guide rails located on either side of the enclosure.

3.Push the ice bin in until resistance is felt. Raise the front slightly and push the ice bin in until an audible “click” is heard.

A

B

A. ON position

B. Auger driver

Ice Production Rate

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

■The ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period.

■To increase ice production, lower the freezer and refrigerator temperature. See “Using the Controls.” Wait 24 hours between adjustments.

Remember

■The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

■Do not use anything sharp to break up the ice in the bin. This can cause damage to the ice bin and dispenser mechanism.

■Do not store anything on top of the ice maker or in the ice storage bin.

Water and Ice Dispenser

IMPORTANT:

■After connecting the refrigerator to a water source, flush the water system. Press the Water button on the dispenser control panel. Use a sturdy container to depress and hold the dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever

(5 seconds on, 5 seconds off) for an additional 2 minutes. This will flush air from the filter and water dispensing system. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.

NOTE: After five minutes of continuous dispensing, the dispenser will stop dispensing water to avoid flooding. To continue dispensing, remove the container and press the dispensing lever again.

■Allow 24 hours for the refrigerator to cool down and chill water. Dispense enough water every week to maintain a fresh supply.

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

Dispense Ice and Water

WARNING

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

1.Select water or cubed ice by pressing the corresponding button on the dispenser control panel. A light above the button indicates your selection.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Refrigerator Safety Refrigerator User InstructionsUnpack the Refrigerator Installation InstructionsRemove the Packaging Clean Before Using Before You Throw Away Your Old Refrigerator or FreezerElectrical Requirements LocationRequirementsRecommended Grounding Method Reverse Osmosis Water Supply Water Supply RequirementsConnect the Water Supply Tools NeededRemove and Replace Handles To Remove Handles Refrigerator Doors and DrawerConnect to Refrigerator To Replace HandlesReplace Doors and Hinges Remove Drawer FrontReplace Drawer Front Remove and Replace Freezer DrawerBottom Hinges Refrigerator USE Adjust the DoorsUsing theControls Opening and Closing DoorsFilter Reset To Adjust Set Point TemperaturesDoor Alarm Temperature Display FCIce Maker and Ice Storage Bin To Access the User Preferences MenuCrisper Humidity Control Water and Ice DispenserRefrigerator Care CleaningTo Clean Your Refrigerator Water Filtration SystemRefrigerator Operation TroubleshootingChanging the Light Bulb Motor seems to run too muchIce and Water Temperature and MoistureTemperature is too warm Refrigerator seems noisyWater Filter Certifications Product Data Sheets Application Guidelines/Water Supply ParametersThis limited warranty does not cover Limited WarrantyItems Excluded from Warranty Disclaimer of Implied Warranties Limitation of RemediesSécurité DU Réfrigérateur RéfrigérateurDéballagedu réfrigérateur Instructions D’INSTALLATIONExigences demplacement Avant de jeter votre vieux réfrigérateur ou congélateurSpécifications de l’alimentationen eau Méthode recommandée de mise à la terreSpécificationsélectriques Raccordement de la canalisation deauPortes ettiroir du réfrigérateur Achever l’installationRaccordement au réfrigérateur Réinstallation de la façade du tiroir Enlèvement de la façade du tiroirCharnières inférieures Ouverture et fermeture des portes Utilisation DU RéfrigérateurAjustement desportes Style 1-Roulettes réglablesDésactivation/activation du refroidissement Utilisationdes commandesHumidity Control commande dhumidité Pour ajuster les réglages de températureRéglage delhumidité dans le bac à légumes Machineà glaçons et bac d’entreposageDistribution de glaçons et d’eau Distributeur d’eau et de glaçonsTaux de production de glaçons Éclairage du distributeurNettoyage Entretien DU RéfrigérateurSystème de filtrationde leau Nettoyage de votre réfrigérateurDépannage Remplacement de l’ampoule d’éclairageFonctionnement du réfrigérateur Glaçons et eau Température et humiditéLes portes sont difficiles à ouvrir Les glaçons sont creux ou petits Feuilles DE Données SUR LE Produit Système de filtration d’eau intérieurArticles Exclus DE LA Garantie Garantie DES Gros Appareils Ménagers Whirlpool CorporationGarantie Limitée La présente garantie limitée ne couvre pas
Top Page Image Contents