Whirlpool W10526085A Installation Requirements, Tools and Parts, Location Requirements

Page 4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Tools needed

■

The cooktop should be installed in a location away from

 

strong draft areas, such as windows, doors and strong

 

heating vents or fans.

■

All openings in the wall or floor where cooktop is to be

 

installed must be sealed.

■Tape measure

■Flat-blade screwdriver

■³⁄₃₂" (#0 [2 mm]) flat-blade screwdriver (screwdriver shaft must be a minimum of 2" [5.1 cm] long)

■¹⁵⁄₁₆" combination wrench

■Pipe wrench

■Wrench or pliers

■Needle-nose pliers

■Marker or pencil

■Pipe-joint compound resistant to LP gas

■Noncorrosive leak-detection solution

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

■ Proper gas supply connection must be available. See “Gas

Supply Requirements” section.

■ The cooktop is designed to hang from the countertop by its

side flanges.

■ The gas and electric supply should be located as shown in

Parts supplied

■Gas pressure regulator

■Burner grates

■Burner caps

■Clamping brackets (2)

■2¹⁄₂" (6.4 cm) clamping screws (2)

Parts needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop base.

A

A. Model/serial rating plate

■To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

“Installation Clearances” section so that they are accessible

without requiring removal of the cooktop.

■ Provide cutout in right rear corner of cutout enclosure as

shown to provide clearance for gas inlet, power supply cord,

and to allow the rating label to be visible.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Product Dimensions

A

B

C

A. 30³⁄₁₆" (76.7 cm) on 30" (76.2 cm) models, 36¹⁄₄" (92.0 cm) on 36" (91.4 cm) models

B. 21" (53.3 cm) C. 3" (7.6 cm)

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation Instructions Cooktop Safety Your safety and the safety of others are very importantPage Tools and Parts Installation RequirementsLocation Requirements Installation Clearances Electrical RequirementsGas Supply Line Gas Supply RequirementsType of Gas Install Cooktop Installing Brackets Before Placing Cooktop in Cutout Installing Brackets After Placing Cooktop in CutoutMake Gas Connection To Assemble Pressure RegulatorComplete Connection Typical flexible connectionComplete Installation Adjust Flame HeightAttach Cooktop to Countertop Check Operation of Surface BurnersAdjustment for Single Valve If you need Assistance or ServiceAdjustment for Dual Valve Page Sécurité DE LA Table DE Cuisson Votre sécurité et celle des autres est très importantePage Exigences demplacement Exigences DinstallationOutillage et pièces Spécifications électriques Dégagements de séparation à respecterCanalisation de gaz Spécifications de lalimentation en gazType de gaz Instructions Dinstallation Installation de la table de cuissonPlan de travail Raccordement au gaz Assemblage du détendeurRaccordement typique par raccord flexible Compléter le raccordementFixation de la table de cuisson Au plan de travail Achever linstallationContrôle du fonctionnement des brûleurs de surface Réglage de la taille des flammes Si le brûleur ne sallume pas correctementAjustement pour un robinet unique Ajustement pour un robinet doubleSi vous avez besoin dassistance ou de service W10526085A

W10526085A specifications

The Whirlpool W10526085A is a premium refrigerator accessory designed to enhance the functionality and efficiency of Whirlpool refrigerators. This innovative replacement filter is engineered to deliver crisp, clean water and ice for the ultimate refreshment experience. With a focus on convenience and aesthetic appeal, it is a must-have component for maintaining high standards of hygiene and quality in your kitchen.

One of the standout features of the W10526085A is its advanced filtration technology. This filter utilizes activated carbon and other specialized materials to remove contaminants and impurities from water, ensuring that the drinking and cooking supply is free from chlorine, lead, and other harmful substances. By effectively reducing these impurities, the filter helps to enhance the taste and clarity of water and ice, making every sip more enjoyable.

Installation of the W10526085A is straightforward and user-friendly. Designed for compatibility with a range of Whirlpool refrigerator models, it can be easily replaced without the need for professional assistance. Simply follow the provided instructions to ensure proper alignment and secure placement, promoting optimal performance right from the start.

Another noteworthy characteristic of this filter is its exceptional filtration life. The W10526085A has a lifespan of up to six months, depending on usage and water quality. Regular replacement is essential to maintain the effectiveness of the filtration system and ensure that your water stays fresh. To help users keep track of replacement schedules, many Whirlpool refrigerators incorporate a filter change indicator, serving as an added convenience.

The W10526085A is also designed with eco-friendliness in mind. By reducing plastic waste associated with bottled water, this filter represents a sustainable choice for households committed to reducing their environmental impact. Moreover, the materials used in manufacturing the filter are often recyclable, further contributing to its green credentials.

In summary, the Whirlpool W10526085A is more than just a refrigerator accessory; it's a vital component for delivering pure, high-quality water and ice. Its advanced filtration capabilities, ease of installation, and commitment to sustainability make it a valuable addition to any Whirlpool refrigerator. By choosing this filter, you’re not only prioritizing health and safety but also enhancing your kitchen's overall functionality.
Top Page Image Contents