Whirlpool W10131955C Complete Installation, Check Flame Height, If burners do not light properly

Page 10

Complete Installation

Electronic Ignition System

Initial lighting and gas flame adjustments

Surface burners use electronic igniters in place of standing pilots. When the cooktop control knob is turned to the “LITE” position, the system creates a spark to light the burner. This sparking continues, as long as the control knob is turned to “LITE.”

Check Flame Height

Adjust the height of surface burner flames.

The surface burner “low” flame should be a steady blue flame approximately ¼" (0.64 cm) high.

A

Check Operation of Surface Burners

Push in and turn the surface burners control knobs to the “LITE” position.

The surface burner flame should light within 4 seconds. The first time a surface burner is lighted it may take longer then 4 seconds to light because of air in the gas line.

Check the flame on “HI” for a blue color. It should be clean and soft in character. No yellow tip, blowing or lifting of flame should occur. Occasional orange flashes are normal and reflect different elements in the air or gas.

After verifying the proper burner operation, turn the control knobs to “OFF.”

If burners do not light properly:

■Turn surface burner control knob to the “OFF” position.

■Check that the power supply cord is plugged in and the circuit breaker has not tripped or the fuse blown.

■Check that the gas shutoff valves are set to the “open” position.

■Check that burner caps are properly positioned on burner bases.

Recheck operation of surface burners. If a burner does not light at this point, contact your dealer or authorized service company for assistance.

B

A.Low flame

B.High flame

If the “low” flame needs to be adjusted:

The flame can be adjusted using the adjustment screw in the center of the valve stem. The valve stem is located directly underneath the control knob.

A

A. Adjustment screw in center of valve stem

1.Remove the control knob.

2.Hold the knob stem with a pair of pliers. Use a small flat- blade screwdriver to turn the screw located in the center of the control knob stem until the flame is the proper size. Turn the screw clockwise to decrease the flame height or counterclockwise to increase the flame height.

3.Replace the control knob.

4.Test the flame by turning the control from “LO” to “HI,” checking the flame at each setting.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation Instructions Cooktop Safety Your safety and the safety of others are very importantTools and Parts Installation RequirementsLocation Requirements Metal Cooktops Product DimensionsCabinet Dimensions Straight-edge glass cooktopsType of Gas Electrical RequirementsGas Supply Requirements Natural GasGas Pressure Regulator Gas Supply Pressure TestingGas Supply Line Burner Input RequirementsPrepare Cooktop for Installation Installation InstructionsInstall Cooktop Make Gas Connection Installing Brackets After Placing Cooktop in CutoutTo Assemble Pressure Regulator Typical flexible connection Attach Cooktop to CountertopComplete Connection Check Flame Height Complete InstallationIf the low flame needs to be adjusted Check Operation of Surface BurnersOn 30 76.2 cm models Wiring DiagramOn 36 91.4 cm models Page Sécurité DE LA Table DE Cuisson Votre sécurité et celle des autres est très importanteExigences demplacement Exigences DinstallationOutillage et pièces Tables de cuisson métalliques Dimensions du produitDimensions du placard Tables de cuisson en verre à bord droitType de gaz Spécifications électriquesSpécifications de lalimentation en gaz Gaz naturelCaractéristiques dalimentation du brûleur Canalisation de gazRégulateur de pression de gaz Test de pressurisation de la canalisation de gazInstallation de la table de cuisson Instructions DinstallationPréparation de la table de cuisson pour Linstallation Style 1 Table de cuisson sur four encastré sous comptoirPlan de travail Bande de mousse Assemblage du détendeur Raccordement au gazRaccordement typique par raccord flexible Compléter le raccordementFixation de la table de cuisson au plan de Travail Vérification de la taille des flammes Achever linstallationContrôle du fonctionnement des brûleurs de surface Si les brûleurs ne sallument pas correctementSur les modèles de 30 76,2 cm Schémas DE CâblageSur les modèles de 36 91,4 cm W10131955C

W10131955C specifications

The Whirlpool W10131955C is a high-performance refrigerator water filter designed to improve the quality of drinking water and ice produced by Whirlpool refrigerators. This filter is known for its innovative features and reliable technology, ensuring that users enjoy fresh, clean water.

One of the standout characteristics of the W10131955C is its advanced filtration system. It utilizes a combination of activated carbon and other filtration materials to effectively reduce contaminants such as chlorine, lead, and other harmful impurities that can affect water taste and quality. This not only enhances the flavor of the water but also provides peace of mind for households concerned about water safety.

The installation process of the W10131955C is user-friendly, allowing homeowners to replace the filter without the need for any special tools. This tool-free installation is a significant advantage, making it accessible for anyone, regardless of their DIY experience. The filter typically requires replacement every six months or after filtering approximately 200 gallons of water, which helps maintain optimal performance and water quality.

In addition to its filtration capabilities, the W10131955C is designed with compatibility in mind. It is specifically designed for use in several Whirlpool, Maytag, KitchenAid, and Jenn-Air refrigerator models. This ensures that a wide range of users can benefit from its advanced filtration technology, making it a versatile choice for families with different appliances.

The W10131955C filter also features an NSF certification, which indicates that it meets strict safety and performance standards. This certification provides additional assurance to consumers about the filter's effectiveness and reliability.

Moreover, the filter's compact design allows for easy storage and reduces waste, contributing to environmentally-friendly practices. By using the W10131955C, households can minimize bottled water usage, thus reducing plastic waste and promoting sustainability.

Overall, the Whirlpool W10131955C is a top-tier water filter that combines advanced technology with user-friendly features. Its efficient filtration system, easy installation, and compatibility with various refrigerator models make it an essential component for anyone looking to ensure that their drinking water is safe, clean, and delicious.
Top Page Image Contents