Whirlpool W10131955C Installation Instructions, Prepare Cooktop for Installation, Install Cooktop

Page 7

INSTALLATION INSTRUCTIONS

Prepare Cooktop for Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install cooktop. Failure to do so can result in back or other injury.

Decide on the final location for the cooktop. Avoid drilling into or severing existing wiring during installation.

On Glass Cooktop models only:

1.Using 2 or more people, place the cooktop upside down on a covered surface.

2.Remove foam strip from the package containing literature. Remove backing from foam strip. Apply foam strip adhesive- side down around bottom of cooktop, flush with edge.

NOTE: The foam strip keeps debris away from the underside of the cooktop and helps the cooktop to sit flat on uneven counters.

A

B

C

A. Cooktop base

B. Foam strip

C. Cooktop

Install Cooktop

Style 1: Cooktop over undercounter built-in oven

IMPORTANT: Clamping brackets should not be used.

1.Using 2 or more people, place cooktop right side up into the cutout.

NOTE: Make sure that the front edge of the cooktop is parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.

Style 2: Cooktop over cabinets

1.Determine whether your cabinet construction provides clearance for installing clamping brackets at cooktop base ends. This is the recommended location. Clamping brackets can be installed on the front and back of cooktop base bottom, if necessary.

A

C

D B

E

A. Attachment screw holes for optional front and back location.

B. Clamping bracket (end locations recommended) C. Cooktop base bottom

D. Attachment screw

E. Attachment screw location (recommended)

2.The clamping brackets can be installed before or after the cooktop is placed into the cutout. Complete the following steps for the option you choose.

Installing Brackets Before Placing Cooktop in Cutout

1.Using 2 or more people, place the cooktop upside down on a covered surface.

2.Remove the attachment screws for the selected bracket locations from the bottom of the cooktop base.

3.Select bracket mounting holes that will allow the bracket to extend far enough out from the cooktop for the installation of 2½" (6.4 cm) clamping screws. See “Attach Cooktop to Countertop” for illustration of clamping screw installation.

A

D

B

C

A. Clamping bracket

B. Recommended attachment screw location

C. Clamping screw location

D. Edge of cooktop base bottom

4.Attach brackets to cooktop base bottom with bracket attachment screws using the bracket mounting holes selected in Step 2.

5.Rotate brackets so they do not extend beyond edge of cooktop base.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

7

Image 7
Contents Installation Instructions Your safety and the safety of others are very important Cooktop SafetyTools and Parts Installation RequirementsLocation Requirements Straight-edge glass cooktops Product DimensionsCabinet Dimensions Metal CooktopsNatural Gas Electrical RequirementsGas Supply Requirements Type of GasBurner Input Requirements Gas Supply Pressure TestingGas Supply Line Gas Pressure RegulatorPrepare Cooktop for Installation Installation InstructionsInstall Cooktop Make Gas Connection Installing Brackets After Placing Cooktop in CutoutTo Assemble Pressure Regulator Typical flexible connection Attach Cooktop to CountertopComplete Connection Check Operation of Surface Burners Complete InstallationIf the low flame needs to be adjusted Check Flame HeightOn 30 76.2 cm models Wiring DiagramOn 36 91.4 cm models Page Votre sécurité et celle des autres est très importante Sécurité DE LA Table DE CuissonExigences demplacement Exigences DinstallationOutillage et pièces Tables de cuisson en verre à bord droit Dimensions du produitDimensions du placard Tables de cuisson métalliquesGaz naturel Spécifications électriquesSpécifications de lalimentation en gaz Type de gazTest de pressurisation de la canalisation de gaz Canalisation de gazRégulateur de pression de gaz Caractéristiques dalimentation du brûleurStyle 1 Table de cuisson sur four encastré sous comptoir Instructions DinstallationPréparation de la table de cuisson pour Linstallation Installation de la table de cuissonPlan de travail Bande de mousse Compléter le raccordement Raccordement au gazRaccordement typique par raccord flexible Assemblage du détendeurFixation de la table de cuisson au plan de Travail Si les brûleurs ne sallument pas correctement Achever linstallationContrôle du fonctionnement des brûleurs de surface Vérification de la taille des flammesSur les modèles de 30 76,2 cm Schémas DE CâblageSur les modèles de 36 91,4 cm W10131955C

W10131955C specifications

The Whirlpool W10131955C is a high-performance refrigerator water filter designed to improve the quality of drinking water and ice produced by Whirlpool refrigerators. This filter is known for its innovative features and reliable technology, ensuring that users enjoy fresh, clean water.

One of the standout characteristics of the W10131955C is its advanced filtration system. It utilizes a combination of activated carbon and other filtration materials to effectively reduce contaminants such as chlorine, lead, and other harmful impurities that can affect water taste and quality. This not only enhances the flavor of the water but also provides peace of mind for households concerned about water safety.

The installation process of the W10131955C is user-friendly, allowing homeowners to replace the filter without the need for any special tools. This tool-free installation is a significant advantage, making it accessible for anyone, regardless of their DIY experience. The filter typically requires replacement every six months or after filtering approximately 200 gallons of water, which helps maintain optimal performance and water quality.

In addition to its filtration capabilities, the W10131955C is designed with compatibility in mind. It is specifically designed for use in several Whirlpool, Maytag, KitchenAid, and Jenn-Air refrigerator models. This ensures that a wide range of users can benefit from its advanced filtration technology, making it a versatile choice for families with different appliances.

The W10131955C filter also features an NSF certification, which indicates that it meets strict safety and performance standards. This certification provides additional assurance to consumers about the filter's effectiveness and reliability.

Moreover, the filter's compact design allows for easy storage and reduces waste, contributing to environmentally-friendly practices. By using the W10131955C, households can minimize bottled water usage, thus reducing plastic waste and promoting sustainability.

Overall, the Whirlpool W10131955C is a top-tier water filter that combines advanced technology with user-friendly features. Its efficient filtration system, easy installation, and compatibility with various refrigerator models make it an essential component for anyone looking to ensure that their drinking water is safe, clean, and delicious.