Whirlpool W10131955C Make Gas Connection, Installing Brackets After Placing Cooktop in Cutout

Page 8

6.Tighten screws just enough to hold brackets in place when cooktop is put in cutout.

7.Using 2 or more people, turn the cooktop right side up and place in cutout.

NOTE: Make sure that the front edge of the cooktop is parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.

8.Loosen the screws and rotate the brackets so that they are perpendicular to the edge of the cooktop base and extend beyond its edge. Securely tighten screws.

Installing Brackets After Placing Cooktop in Cutout

1.Using 2 or more people, place cooktop right side up into the cutout.

NOTE: Make sure that the front edge of the cooktop is parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.

2.Remove the attachment screws for the selected bracket locations from the bottom of the cooktop base.

3.Select bracket mounting holes that will allow the bracket to extend far enough out from the cooktop for the installation of 2½" (6.4 cm) clamping screws.

G

A

 

B

F

 

 

E

 

D

C

A.Cooktop

B.Cooktop base

C.Attachment screw

D.Clamping bracket (extends far enough beyond cooktop base to allow installation of clamping screws)

E.2½" (6.4 cm) clamping screw (to be installed in “Attach Cooktop to Countertop”)

F.Countertop G. Foam seal

4.Attach brackets to cooktop base bottom with bracket attachment screws using the bracket mounting holes selected in Step 3. Securely tighten screws.

Make Gas Connection

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

To Assemble Pressure Regulator:

1.Using 2 or more people, stand the cooktop on its side or back.

2.Connect the flexible stainless steel connector to the pressure regulator using a ½" male pipe thread adapter and nipple.

A combination of pipe fittings must be used to connect the cooktop to the existing gas line. Shown following is a typical connection. Your connection may be different, according to the supply line type, size and location.

3.Install the pressure regulator with the arrow pointing up toward the bottom of the cooktop base and in a position where you can reach the regulator cap.

B

A

C

D

A. Access cap

B. Rear of cooktop

C. Gas pressure regulator

D. Up arrow. Regulator must be installed with arrow pointing up to cooktop bottom.

IMPORTANT: All connections must be wrench-tightened. Do not make connections to the gas regulator too tight. Making the connections too tight may crack the regulator and cause a gas leak. Do not allow the regulator to turn on the pipe when tightening fittings.

Use only pipe-joint compound made for use with Natural and LP gas.

Do not use TEFLON® tape. You will need to determine the fittings required depending on your installation.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Installation Instructions Cooktop Safety Your safety and the safety of others are very importantLocation Requirements Installation RequirementsTools and Parts Product Dimensions Cabinet DimensionsMetal Cooktops Straight-edge glass cooktopsElectrical Requirements Gas Supply RequirementsType of Gas Natural GasGas Supply Pressure Testing Gas Supply LineGas Pressure Regulator Burner Input RequirementsInstall Cooktop Installation InstructionsPrepare Cooktop for Installation To Assemble Pressure Regulator Installing Brackets After Placing Cooktop in CutoutMake Gas Connection Complete Connection Attach Cooktop to CountertopTypical flexible connection Complete Installation If the low flame needs to be adjustedCheck Flame Height Check Operation of Surface BurnersOn 36 91.4 cm models Wiring DiagramOn 30 76.2 cm models Page Sécurité DE LA Table DE Cuisson Votre sécurité et celle des autres est très importanteOutillage et pièces Exigences DinstallationExigences demplacement Dimensions du produit Dimensions du placardTables de cuisson métalliques Tables de cuisson en verre à bord droitSpécifications électriques Spécifications de lalimentation en gazType de gaz Gaz naturelCanalisation de gaz Régulateur de pression de gazCaractéristiques dalimentation du brûleur Test de pressurisation de la canalisation de gazInstructions Dinstallation Préparation de la table de cuisson pour LinstallationInstallation de la table de cuisson Style 1 Table de cuisson sur four encastré sous comptoirPlan de travail Bande de mousse Raccordement au gaz Raccordement typique par raccord flexibleAssemblage du détendeur Compléter le raccordementFixation de la table de cuisson au plan de Travail Achever linstallation Contrôle du fonctionnement des brûleurs de surfaceVérification de la taille des flammes Si les brûleurs ne sallument pas correctementSur les modèles de 36 91,4 cm Schémas DE CâblageSur les modèles de 30 76,2 cm W10131955C

W10131955C specifications

The Whirlpool W10131955C is a high-performance refrigerator water filter designed to improve the quality of drinking water and ice produced by Whirlpool refrigerators. This filter is known for its innovative features and reliable technology, ensuring that users enjoy fresh, clean water.

One of the standout characteristics of the W10131955C is its advanced filtration system. It utilizes a combination of activated carbon and other filtration materials to effectively reduce contaminants such as chlorine, lead, and other harmful impurities that can affect water taste and quality. This not only enhances the flavor of the water but also provides peace of mind for households concerned about water safety.

The installation process of the W10131955C is user-friendly, allowing homeowners to replace the filter without the need for any special tools. This tool-free installation is a significant advantage, making it accessible for anyone, regardless of their DIY experience. The filter typically requires replacement every six months or after filtering approximately 200 gallons of water, which helps maintain optimal performance and water quality.

In addition to its filtration capabilities, the W10131955C is designed with compatibility in mind. It is specifically designed for use in several Whirlpool, Maytag, KitchenAid, and Jenn-Air refrigerator models. This ensures that a wide range of users can benefit from its advanced filtration technology, making it a versatile choice for families with different appliances.

The W10131955C filter also features an NSF certification, which indicates that it meets strict safety and performance standards. This certification provides additional assurance to consumers about the filter's effectiveness and reliability.

Moreover, the filter's compact design allows for easy storage and reduces waste, contributing to environmentally-friendly practices. By using the W10131955C, households can minimize bottled water usage, thus reducing plastic waste and promoting sustainability.

Overall, the Whirlpool W10131955C is a top-tier water filter that combines advanced technology with user-friendly features. Its efficient filtration system, easy installation, and compatibility with various refrigerator models make it an essential component for anyone looking to ensure that their drinking water is safe, clean, and delicious.
Top Page Image Contents