Whirlpool Gas Built-In Cooktop Installation Requirements, Tools and Parts, Location Requirements

Page 3

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Tools needed

Tape measure

Marker or pencil

Flat-blade screwdriver

Pipe-joint compound

¹⁵⁄₁₆" combination wrench

 

resistant to LP gas

Noncorrosive leak-detection

Pipe wrench

 

solution

 

 

 

Wrench or pliers

Parts supplied

Gas pressure regulator

Burner grates

Burner caps

Clamping brackets (2)

2¹⁄₂" (6.4 cm) clamping screws (2)

Parts needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

Grounded electrical supply is required. See “Electrical Requirements” section. Proper gas supply connection must be available. See “Gas Supply Requirements” section.

The cooktop is designed to hang from the countertop by its side or rear flanges.

The gas and electric supply should be located as shown in “Cabinet Dimensions” section so that they are accessible without requiring removal of the cooktop.

Provide cutout in right rear corner of cutout enclosure as shown to provide clearance for gas inlet, power supply cord, and to allow the rating label to be visible.

IMPORTANT: To avoid damage, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Mobile Home - Additional Installation Requirements

The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop base.

A

A. Model/serial rating plate

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

All openings in the wall or floor where cooktop is to be installed must be sealed.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

Product Dimensions

Metal Cooktops

A

B

C

A. 31⁷⁄₁₆" (79.8 cm) on 30" (76.2 cm) models, 37⁹⁄₁₆" (95.4 cm) on 36" (91.4 cm) models

B.21¹⁄₄" (53.4 cm)

C.2⁷⁄₈" (7.3 cm)

Straight-edge glass cooktops

B

A C

A.20⁵⁄₁₆" (51.5 cm)

B.30³⁄₁₆" (76.8 cm) on 30" (76.2 cm) models, 36⁷⁄₁₆" (92.5 cm) on 36" (91.4 cm) models

C.2⁷⁄₈" (7.3 cm)

3

Image 3
Contents Installation Instructions Your safety and the safety of others are very important Cooktop SafetyInstallation Requirements Tools and PartsLocation Requirements Cabinet Dimensions Electrical RequirementsCurved-edge glass cooktops Gas Pressure Regulator Gas Supply RequirementsType of Gas Gas Supply LineInstallation Instructions Prepare Cooktop for InstallationInstall Cooktop Installing Brackets After Placing Cooktop in Cutout Make Gas ConnectionTo Assemble Pressure Regulator Attach Cooktop to Countertop Typical flexible connectionComplete Connection Check Flame Height Complete InstallationIf the low flame needs to be adjusted Check Operation of Surface BurnersOn 30 76.2 cm models On 36 91.4 cm models Wiring DiagramsVotre sécurité et celle des autres est très importante Sécurité DE LA Table DE CuissonExigences Dinstallation Exigences demplacementOutillage et pièces Tables de cuisson en verre à bord droit Dimensions du produitDimensions du placard Tables de cuisson métalliquesGaz naturel Spécifications électriquesSpécifications de lalimentation en gaz Type de gazTest de pressurisation de la canalisation de gaz Canalisation de gazRégulateur de pression de gaz Caractéristiques dalimentation du brûleurStyle 1 Table de cuisson sur four encastré sous comptoir Instructions DinstallationPréparation de la table de cuisson Pour linstallation Installation de la table de cuissonAssemblage du détendeur Raccordement au gazFixation de la table de cuisson au plan De travail Raccordement typique par raccord flexibleCompléter le raccordement Si les brûleurs ne sallument pas correctement Achever linstallationVérification de la taille sdes flammes Contrôle du fonctionnement des brûleurs de surfaceW10131955B Schémas DE CâblageSur les modèles de 30 76,2 cm Sur les modèles de 36 91,4 cm

Gas Built-In Cooktop specifications

The Whirlpool Gas Built-In Cooktop is a versatile and stylish addition to any modern kitchen, engineered to deliver exceptional cooking performance while seamlessly integrating into your kitchen design. Its sleek, built-in configuration offers a clean and sophisticated look, making it an excellent choice for both contemporary and traditional décor.

One of the standout features of the Whirlpool Gas Cooktop is its powerful burners, which provide efficient heat distribution for precise cooking control. The cooktop typically comes equipped with multiple burners, including high-output options that are perfect for boiling, searing, and stir-frying. The simmer burner is designed for delicate tasks like sauces or melting chocolate, ensuring that your culinary creations achieve the desired texture and flavor without risk of scorching.

Incorporating advanced technology, Whirlpool’s cooktops often feature a continuous grates design, allowing for smooth transitions between burners. This feature not only enhances stability when moving pots and pans but also simplifies the task of managing multiple cooking items simultaneously. The grates are usually made from cast iron, providing durability and excellent heat retention, which can elevate your cooking experience.

The cooktop’s ignition system is designed for user-friendly operation. With a simple push-to-turn knob, you can ignite the burners safely and quickly. Many models are equipped with electronic ignition, which means that the burners will light with ease each time you use them, eliminating the need for matches or lighters.

For added convenience and ease of cleaning, the Whirlpool Gas Cooktop features sealed burners. This design prevents spills and debris from seeping into the burner compartment, making cleanup a breeze. The surface is typically composed of premium materials that resist scratches and stains, ensuring that your cooktop maintains its polished appearance even after daily use.

Furthermore, you can often find adjustable burner settings that allow for greater flexibility in cooking styles. Whether you’re simmering sauces, boiling pasta, or achieving the perfect caramelization on meats, the ability to fine-tune the heat output is a major advantage for home cooks and culinary enthusiasts alike.

Overall, the Whirlpool Gas Built-In Cooktop exemplifies a perfect blend of performance, style, and technology, making it a smart choice for anyone looking to enhance their kitchen. With its robust features, user-friendly design, and reliability, it stands as a testament to Whirlpool's commitment to delivering high-quality home appliances that make cooking enjoyable and efficient.