Whirlpool Gas Built-In Cooktop Installation Instructions, Prepare Cooktop for Installation

Page 6

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not applicable for Canada).

For elevations above 6,560 ft (1999.5 m) a high altitude kit is needed to avoid any reduced power output. See separate LP gas conversion instructions sheet.

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" water column pressure above the manifold pressure shown on the model/serial rating plate.

Line pressure testing above ½ psi gauge (14" WCP)

The cooktop and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).

Line pressure testing at ½ psi gauge (14" WCP) or lower

The cooktop must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).

INSTALLATION INSTRUCTIONS

Prepare Cooktop for Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install cooktop. Failure to do so can result in back or other injury.

Decide on the final location for the cooktop. Avoid drilling into or severing existing wiring during installation.

On Glass Cooktop models only:

1.Using 2 or more people, place the cooktop upside down on a covered surface.

2.Remove foam strip from package containing literature. Remove backing from foam strip. Apply foam strip adhesive- side down around bottom of cooktop, flush with edge.

NOTE: The foam strip protects the underside of the cooktop glass from debris and helps the cooktop sit flat on uneven counters.

A

B

C

A. Cooktop base

B. Foam strip

C. Cooktop

Install Cooktop

Style 1: Cooktop over undercounter built-in oven

IMPORTANT: Clamping brackets should not be used.

1.Using 2 or more people, place cooktop right side up into the cutout.

NOTE: Make sure that the front edge of the cooktop is parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.

Style 2: Cooktop over cabinets

1.Determine whether your cabinet construction provides clearance for installing clamping brackets at cooktop base ends. This is the recommended location. Clamping brackets can be installed on the front and back of cooktop base bottom, if necessary.

A

C

D B

E

A. Attachment screw holes for optional front and back location.

B. Clamping bracket (end locations recommended) C. Cooktop base bottom

D. Attachment screw

E. Attachment screw location (recommended)

2.The clamping brackets can be installed before or after the cooktop is placed into the cutout. Complete the following steps for the option you choose.

Installing Brackets Before Placing Cooktop in Cutout

1.Using 2 or more people, place the cooktop upside down on a covered surface.

2.Remove the attachment screws for the selected bracket locations from the bottom of the cooktop base.

3.Select bracket mounting holes that will allow the bracket to extend far enough out from the cooktop for the installation of 2½" (6.4 cm) clamping screws. See “Attach Cooktop to Countertop” for illustration of clamping screw installation.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Instructions Cooktop Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsLocation Requirements Cabinet Dimensions Electrical RequirementsCurved-edge glass cooktops Gas Supply Line Gas Supply RequirementsType of Gas Gas Pressure RegulatorInstallation Instructions Prepare Cooktop for InstallationInstall Cooktop Installing Brackets After Placing Cooktop in Cutout Make Gas ConnectionTo Assemble Pressure Regulator Attach Cooktop to Countertop Typical flexible connectionComplete Connection Check Operation of Surface Burners Complete InstallationIf the low flame needs to be adjusted Check Flame HeightWiring Diagrams On 30 76.2 cm models On 36 91.4 cm modelsSécurité DE LA Table DE Cuisson Votre sécurité et celle des autres est très importanteExigences Dinstallation Exigences demplacementOutillage et pièces Tables de cuisson métalliques Dimensions du produitDimensions du placard Tables de cuisson en verre à bord droitType de gaz Spécifications électriquesSpécifications de lalimentation en gaz Gaz naturelCaractéristiques dalimentation du brûleur Canalisation de gazRégulateur de pression de gaz Test de pressurisation de la canalisation de gazInstallation de la table de cuisson Instructions DinstallationPréparation de la table de cuisson Pour linstallation Style 1 Table de cuisson sur four encastré sous comptoirRaccordement au gaz Assemblage du détendeurFixation de la table de cuisson au plan De travail Raccordement typique par raccord flexibleCompléter le raccordement Contrôle du fonctionnement des brûleurs de surface Achever linstallationVérification de la taille sdes flammes Si les brûleurs ne sallument pas correctementSur les modèles de 36 91,4 cm Schémas DE CâblageSur les modèles de 30 76,2 cm W10131955B

Gas Built-In Cooktop specifications

The Whirlpool Gas Built-In Cooktop is a versatile and stylish addition to any modern kitchen, engineered to deliver exceptional cooking performance while seamlessly integrating into your kitchen design. Its sleek, built-in configuration offers a clean and sophisticated look, making it an excellent choice for both contemporary and traditional décor.

One of the standout features of the Whirlpool Gas Cooktop is its powerful burners, which provide efficient heat distribution for precise cooking control. The cooktop typically comes equipped with multiple burners, including high-output options that are perfect for boiling, searing, and stir-frying. The simmer burner is designed for delicate tasks like sauces or melting chocolate, ensuring that your culinary creations achieve the desired texture and flavor without risk of scorching.

Incorporating advanced technology, Whirlpool’s cooktops often feature a continuous grates design, allowing for smooth transitions between burners. This feature not only enhances stability when moving pots and pans but also simplifies the task of managing multiple cooking items simultaneously. The grates are usually made from cast iron, providing durability and excellent heat retention, which can elevate your cooking experience.

The cooktop’s ignition system is designed for user-friendly operation. With a simple push-to-turn knob, you can ignite the burners safely and quickly. Many models are equipped with electronic ignition, which means that the burners will light with ease each time you use them, eliminating the need for matches or lighters.

For added convenience and ease of cleaning, the Whirlpool Gas Cooktop features sealed burners. This design prevents spills and debris from seeping into the burner compartment, making cleanup a breeze. The surface is typically composed of premium materials that resist scratches and stains, ensuring that your cooktop maintains its polished appearance even after daily use.

Furthermore, you can often find adjustable burner settings that allow for greater flexibility in cooking styles. Whether you’re simmering sauces, boiling pasta, or achieving the perfect caramelization on meats, the ability to fine-tune the heat output is a major advantage for home cooks and culinary enthusiasts alike.

Overall, the Whirlpool Gas Built-In Cooktop exemplifies a perfect blend of performance, style, and technology, making it a smart choice for anyone looking to enhance their kitchen. With its robust features, user-friendly design, and reliability, it stands as a testament to Whirlpool's commitment to delivering high-quality home appliances that make cooking enjoyable and efficient.
Top Page Image Contents