Whirlpool W10282149B manual Condenser Dirty or clogged condenser, Interior Components

Page 10

8.After the cleaning cycle is complete, remove the drain cap from the water pan. Look for any cleaning solution left in the water pan. If cleaning solution drains from the water pan, you should run the clean cycle again. Be sure to replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan and you will have either thin ice or no ice.

NOTE: Severe scale buildup may require repeated cleaning with a fresh quantity of cleaning solution.

9.Press the ON button to resume ice production.

Condenser

A dirty or clogged condenser:

■Obstructs proper airflow.

■Reduces ice making capacity.

■Causes higher than recommended operating temperatures which may lead to component failure.

WARNING

Electrical Shock Hazard

Disconnect power before cleaning.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug ice maker or disconnect power.

2.Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support.

3.Pull the bottom forward and then pull down to remove the lower access panel.

4.Remove dirt and lint from the condenser fins and the unit compartment with a brush attachment on a vacuum cleaner.

5.Replace the lower access panel using the four screws.

6.Plug in ice maker or reconnect power.

Interior Components

1.Unplug ice maker or disconnect power.

2.Open the storage bin door and remove any ice that is in the bin.

3.Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

4.Remove the two screws that hold the cutter grid cover in place and remove the cutter grid cover.

5.Unplug the wiring harness from the left side of the cutter grid.

A

B

A. Cutter grid cover

B.Screws

6.Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

7.Remove the right-hand and left-hand screws. Lift the cutter grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

D

A

 

B

E

C

F

 

A. Cutter grid harness

D. Ice level sensor harness

B. Screw

E. Plastic spacer

C. Cutter grid

F. Screw

8.Remove the two thumb screws that hold the water pan in place. Push down with one hand on the front of the pan while pulling forward on the bottom back side.

B

A

B

C

A. Water pan

B. Water pan thumb screws

C. Drain cap

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents ICE Maker W10282149BICE Maker Safety Table of ContentsTable DES Matières Unpack the IceMaker Installation InstructionsCleaning Before Use LocationRequirementsLeveling Electrical RequirementsWater Supply Requirements Recommended grounding methodConnect Water Supply Connecting the Water LineRear View Gravity Drain System Connecting the DrainDrain Connection Side View Top Hinge Ice Maker Door Bottom Hinge How Your Ice Maker Works ICE Maker USENormalSounds Reverse Door CatchCleaning Using the ControlsICE Maker Care Cutter grid cover Screws Condenser Dirty or clogged condenserInterior Components Cutter grid harnessTo shut down the ice maker For ice makers with a drain pump installedVacationand Moving Care Thumb screws Ice scoop holderTroubleshooting Ice Maker OperationIce Quality Assistance or ServicePlumbing Problems U.S.AThis limited warranty does not cover Limited WarrantyItems Excluded from Warranty Disclaimer of Implied Warranties Limitation of RemediesDéballage de la machine à glaçons Instructions D’INSTALLATIONSécurité DE LA Machine À Glaçons Nettoyage avant l’utilisationSpécifications électriques Exigences demplacementMéthode de mise à la terre recommandée Spécifications del’alimentationen eauOutillage nécessaire NivellementRaccordement à la canalisation d’eau Raccordement du tuyau d’eauVUE Arrière Raccordementau drain de vidangeVidange par gravité Raccordement du drain de vidange VUE LatéraleSystème avec pompe de vidange sur certains modèles Charnière supérieure Porte de la machine à glaçonsCharnière inférieure Sons normaux GlaçonsFonctionnement dela machine à glaçons Inversion du loquet de porteUtilisation des commandes NettoyageBac à eau Vis à ailette du bac à eau Capuchon de vidange Condenseur Un condenseur sale ou bouchéComposants intérieurs Couvercle de la grille de coupe VisPrécautions à prendre avant les vacances Ou un déménagement Arrêt de la machine à glaçonsProductionde glaçons DépannageFonctionnement de la machine à glaçons Machine à glaçons avec pompe de vidangeProblèmes de plomberie Assistance OU ServiceQualité des glaçons Si vous avez besoin de pièces de rechangeGarantie Limitée Garantie DES Gros Appareils Ménagers Whirlpool CorporationPour plus d’assistance Articles Exclus DE LA GarantieW10282149B Whirlpool Corporation 12/10 All rights reserved
Top Page Image Contents