Whirlpool 2208357 manual Cleaningthe Interior Components

Page 14

4.Remove dirt and lint from the condenser fins and the unit compartment with a brush attachment on a vacuum cleaner.

5.Replace the lower access panel using the four screws.

6.Plug in ice maker or reconnect power.

7.Remove the right-hand screw and loosen the left-hand screw. Lift the cutter grid up and out and over the left- hand screw.

NOTE: Make sure the plastic spacer from the right- hand side of the cutter grid bracket stays with the cutter grid.

Cleaningthe Interior

Components

1.Unplug ice maker or disconnect power.

2.Open the storage bin door and remove any ice that is in the bin.

3.Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap.

4.Remove the three screws that hold the cutter grid cover in place.

5.Unplug the wiring harness from the left side of the cutter grid.

1.Cutter Grid Cover

2.Screws

6.Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

1.Cutter Grid Harness

2.Screw

3.Cutter Grid

4.Ice Level Sensor Harness

5.Plastic Spacer

6.Screw

8.Remove the two screws that hold the water pan in place. Push down with one hand on the front of the pan while pulling forward on the bottom back side.

9.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, and ice scoop with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tablespoon (15 mL) of household bleach in 1 gallon (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

10.Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws.

11.Check the following:

■Drain cap from the water pan is in place.

■Hose from water pan is inserted into storage bin drain opening.

12.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid and ice level sensor harnesses.

13.Plug in ice maker or reconnect power.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 2208357 Use &CareGuideGuide d’utilisation Et d’entretien Contents Table DES MatièresICE Maker Safety Your safety and the safety of others is very importantParts and Features Unpacking theIce Maker Cleaning before useICE Maker Space RequirementsLevelingthe Ice Maker Undercounter installationElectrical Requirements Recommended grounding methodConnecting the water line ConnectingtheIceMakertoa Water SourceFreestanding installation To adjust the front leveling legsRear View Front ViewSide View Connecting the drainReversingtheDoor Swing To reverse the hinges Top HingeBottom Hinge To replace door on hingesUnderstandingHowYour Ice Maker Works Using Your ICE MakerMayHear Making IceSetting the Controls Cleaning ExteriorSurfacesCleaning the Ice Maker System Cleaning the CondenserCleaningthe Interior Components To shut down the ice maker For ice makers with a drain pump installedVacationandMovingCare Trouble Shooting Canada Assistance Or ServiceU.S.A Whirlpool will not pay for ONE-YEAR Full WarrantyFIVE-YEAR Full Warranty Sécurité DE LA Machine À Glaçons Votre sécurité et celle des autres est très importantePièces ET Caractéristiques Enlèvement des matériaux d’emballage Déballage delamachineà GlaçonsEspace requis Nettoyage avant l’utilisationMised’aplombdelamachineà Glaçons Méthode de mise à la terre recommandéeSpécificationsélectriques Outillage requisRaccordement du tuyau d’eau Raccordement delamachine àglaçons àl’alimentation eneauLire toutes les instructions avec soin avant de commencer Ajustement deux pieds de nivellement avantVUE Arrière VUE AvantVUE Latérale Raccordement de la vidangeVidange par gravité Système à pompe de vidange sur certains modèlesInversion des charnières DelaportePour retirer la porte des charnières Charnière inférieure Réinstallion de la porte sur les charnièresCharnière supérieure Inversion du loquet de porteGlaçons Fabrication de la glaceNettoyage dessurfaces Extérieures Réglagedes commandesMachine À Glaçons Machineà glaçons Nettoyage du condenseurNettoyage descomposants Intérieurs Machine à glaçons avec pompe de drainage Lesvacances oule DéménagementArrêt de la machine à glaçons La machine fonctionne, mais ne produit pas de glace DépannageLa machine fonctionne, mais produit très peu de glace Les glaçons ont un goûtAuxÉtats-Unis Assistance OU ServiceAuCanada Whirlpool Corporation ne paiera pas pour Garantie Complète DE UN ANGarantie Complète DE Cinq ANS Pour des renseignements sur la garantie au Canada2208357

2208357 specifications

The Whirlpool 2208357 is a highly regarded appliance that stands out in the world of refrigerators, particularly known for its adept design and a host of functional features aimed at enhancing the user experience. This refrigerator exemplifies Whirlpool's commitment to quality and innovation, offering consumers a blend of style and practicality.

One of the primary features of the Whirlpool 2208357 is its spacious interior, designed to accommodate a variety of food items. This refrigerator boasts adjustable shelves, allowing users to customize the interior layout according to their storage needs. The flexible storage options make it easy to store tall bottles or large containers without compromising space.

The refrigerator is also equipped with a sophisticated cooling system that ensures even temperature distribution. This technology prevents hotspots, helping to maintain the freshness of food items longer. Additionally, the presence of humidity-controlled crispers prolongs the lifespan of fruits and vegetables by regulating humidity levels, ensuring they remain fresh and crisp.

Energy efficiency is another hallmark of the Whirlpool 2208357. The appliance is designed to consume less electricity while delivering top-notch performance. This energy-efficient design not only helps in reducing utility bills but also reflects an eco-friendly commitment.

Moreover, the Whirlpool 2208357 features a user-friendly control panel, making it easy for users to adjust temperatures and settings with ease. The intuitive display provides quick access to various functions, enhancing the overall user experience.

In terms of design, the Whirlpool 2208357 offers a sleek and modern aesthetic that fits seamlessly into any kitchen decor. Available in various finishes, it can complement both contemporary and traditional kitchens. The appliance's door design also adds to its stylish appearance while ensuring durability.

Built with quality materials, the Whirlpool 2208357 promises longevity and reliability, catering to the needs of families and individuals alike. Its robust construction minimizes the chances of wear and tear, making it a worthwhile investment for any household.

In summary, the Whirlpool 2208357 is an exemplary refrigerator known for its spacious interior, advanced cooling technologies, energy efficiency, and user-friendly features. Its modern design combined with durability makes it a preferred choice for consumers looking for a reliable and stylish kitchen appliance.
Top Page Image Contents