Whirlpool 2208357 manual ConnectingtheIceMakertoa Water Source, Freestanding installation

Page 7

To adjust the front leveling legs

Your ice maker has two adjustable leveling legs to help you steady the product and make sure it is level.

SUGGESTION: It is easier to adjust the leveling legs if you have another person to assist you.

1.Place a carpenter’s level on top of the product to see if the ice maker is level from front to back and side to side.

2.Push up on the top front of the ice maker, and then locate the leveling screws that are on the bottom front of the product.

3.Using an adjustable wrench, change the height of the legs as follows:

■Turn the leveling leg to the right to lower that side of the ice maker.

■Turn the leveling leg to the left to raise that side of the ice maker.

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

4.Use a carpenter’s level to re-check the ice maker to see that it is even from front to back and side to side. If the ice maker is not level, repeat Steps 2 and 3. If the ice maker is level, go to the “Connecting the Ice Maker to a Water Source” section.

Freestanding installation

If you are not installing your ice maker under a countertop, you will probably not need to adjust the rear wheel height. Follow the steps outlined in “To adjust the front leveling legs” earlier in this section.

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

ConnectingtheIceMakertoa

Water Source

Read all directions carefully before you begin.

IMPORTANT:

■All installations must be in accordance with local plumbing codes requirements.

■Use copper tubing and check for leaks.

■Install copper tubing only in areas where temperatures will remain above freezing.

Tools required:

■Standard screwdriver

■⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches

■¹⁄₄" nut driver

■¹⁄₄" drill bit

■Hand drill or electric drill properly grounded

NOTE: Your ice maker dealer has a kit available with a ¹⁄₄" (.635 cm) saddle-type shut-off valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄₁₆" (.476 cm) saddle valve which reduces water flow and clogs more easily.

Connecting the water line:

1.Turn off main water supply. Turn on nearest faucet long enough to clear line of water.

2.Find a ¹⁄₂" (1.27 cm) to 1¹⁄₄" (3.18 cm) vertical cold water pipe near the ice maker.

NOTE: Horizontal pipe will work, but the following

procedure must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

3.Using a grounded drill, drill a ¹⁄₄" (.635 cm) hole in the cold water pipe you have selected.

4.Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the ¹⁄₄” (.635 cm) drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten the pipe clamp or you may crush cold water pipe if it is soft copper tubing. Do not use a piercing-type or ³⁄₁₆" (.476 cm) saddle-type valve which reduces water flow and clogs more easily.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Guide d’utilisation Et d’entretien Use &CareGuide2208357 Table DES Matières ContentsYour safety and the safety of others is very important ICE Maker SafetyParts and Features Space Requirements Cleaning before useICE Maker Unpacking theIce MakerRecommended grounding method Undercounter installationElectrical Requirements Levelingthe Ice MakerTo adjust the front leveling legs ConnectingtheIceMakertoa Water SourceFreestanding installation Connecting the water lineFront View Rear ViewReversingtheDoor Swing Connecting the drainSide View To replace door on hinges Top HingeBottom Hinge To reverse the hingesMaking Ice Using Your ICE MakerMayHear UnderstandingHowYour Ice Maker WorksCleaning ExteriorSurfaces Setting the ControlsCleaning the Condenser Cleaning the Ice Maker SystemCleaningthe Interior Components VacationandMovingCare For ice makers with a drain pump installedTo shut down the ice maker Trouble Shooting U.S.A Assistance Or ServiceCanada FIVE-YEAR Full Warranty ONE-YEAR Full WarrantyWhirlpool will not pay for Votre sécurité et celle des autres est très importante Sécurité DE LA Machine À GlaçonsPièces ET Caractéristiques Nettoyage avant l’utilisation Déballage delamachineà GlaçonsEspace requis Enlèvement des matériaux d’emballageOutillage requis Méthode de mise à la terre recommandéeSpécificationsélectriques Mised’aplombdelamachineà GlaçonsAjustement deux pieds de nivellement avant Raccordement delamachine àglaçons àl’alimentation eneauLire toutes les instructions avec soin avant de commencer Raccordement du tuyau d’eauVUE Avant VUE ArrièreSystème à pompe de vidange sur certains modèles Raccordement de la vidangeVidange par gravité VUE LatéralePour retirer la porte des charnières DelaporteInversion des charnières Inversion du loquet de porte Réinstallion de la porte sur les charnièresCharnière supérieure Charnière inférieureFabrication de la glace GlaçonsMachine À Glaçons Réglagedes commandesNettoyage dessurfaces Extérieures Nettoyage du condenseur Machineà glaçonsNettoyage descomposants Intérieurs Arrêt de la machine à glaçons Lesvacances oule DéménagementMachine à glaçons avec pompe de drainage Les glaçons ont un goût DépannageLa machine fonctionne, mais produit très peu de glace La machine fonctionne, mais ne produit pas de glaceAuCanada Assistance OU ServiceAuxÉtats-Unis Pour des renseignements sur la garantie au Canada Garantie Complète DE UN ANGarantie Complète DE Cinq ANS Whirlpool Corporation ne paiera pas pour2208357

2208357 specifications

The Whirlpool 2208357 is a highly regarded appliance that stands out in the world of refrigerators, particularly known for its adept design and a host of functional features aimed at enhancing the user experience. This refrigerator exemplifies Whirlpool's commitment to quality and innovation, offering consumers a blend of style and practicality.

One of the primary features of the Whirlpool 2208357 is its spacious interior, designed to accommodate a variety of food items. This refrigerator boasts adjustable shelves, allowing users to customize the interior layout according to their storage needs. The flexible storage options make it easy to store tall bottles or large containers without compromising space.

The refrigerator is also equipped with a sophisticated cooling system that ensures even temperature distribution. This technology prevents hotspots, helping to maintain the freshness of food items longer. Additionally, the presence of humidity-controlled crispers prolongs the lifespan of fruits and vegetables by regulating humidity levels, ensuring they remain fresh and crisp.

Energy efficiency is another hallmark of the Whirlpool 2208357. The appliance is designed to consume less electricity while delivering top-notch performance. This energy-efficient design not only helps in reducing utility bills but also reflects an eco-friendly commitment.

Moreover, the Whirlpool 2208357 features a user-friendly control panel, making it easy for users to adjust temperatures and settings with ease. The intuitive display provides quick access to various functions, enhancing the overall user experience.

In terms of design, the Whirlpool 2208357 offers a sleek and modern aesthetic that fits seamlessly into any kitchen decor. Available in various finishes, it can complement both contemporary and traditional kitchens. The appliance's door design also adds to its stylish appearance while ensuring durability.

Built with quality materials, the Whirlpool 2208357 promises longevity and reliability, catering to the needs of families and individuals alike. Its robust construction minimizes the chances of wear and tear, making it a worthwhile investment for any household.

In summary, the Whirlpool 2208357 is an exemplary refrigerator known for its spacious interior, advanced cooling technologies, energy efficiency, and user-friendly features. Its modern design combined with durability makes it a preferred choice for consumers looking for a reliable and stylish kitchen appliance.
Top Page Image Contents