Whirlpool 2208357 ICE Maker, Unpacking theIce Maker, Space Requirements, Cleaning before use

Page 5

INSTALLING YOUR

ICE MAKER

Unpacking theIce Maker

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

Removing packaging materials

IMPORTANT: Do not remove any permanent instruction labels inside your ice maker or the Tech Sheet that is fastened behind the lower access panel.

Space Requirements

■To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The unit may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

■Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shut-off valve and either a gravity-drain system or condensate pump to carry the water to an existing drain.

■Choose a well ventilated area with temperatures above 55°F (13°C) and below 100°F (38°C). Best results are obtained between 70°F (21°C) and 90°F (32°C). This unit MUST be installed in an area protected from the elements, such as wind, rain, water spray, or drip.

■When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as shown.

NOTE: Do not kink or pinch the power supply cord between the ice maker and cabinet.

■Remove tape and any labels from your ice maker before using (except the model and serial number label).

■To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

■Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your ice maker.

Cleaning before use

34"

(86.4 cm)

Min.

341/2"

(87.6 cm)

Max.

111/2" (29.2 cm)

31/2" 9"

(8.9 cm) (22.9 cm)

24"

(60.1 cm)

281/2"

(72.4 cm)

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in the “Caring for Your Ice Maker” section.

15"

(38.1 cm)

1.Recommended Location for Electrical and Plumbing Fixtures.

2.Floor Level

■You should choose a location where the floor is even. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the position of the rear wheels. See the “Leveling the Ice Maker” section.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 2208357 Use &CareGuideGuide d’utilisation Et d’entretien Table DES Matières ContentsYour safety and the safety of others is very important ICE Maker SafetyParts and Features ICE Maker Cleaning before useUnpacking theIce Maker Space RequirementsElectrical Requirements Undercounter installationLevelingthe Ice Maker Recommended grounding methodFreestanding installation ConnectingtheIceMakertoa Water SourceConnecting the water line To adjust the front leveling legsFront View Rear ViewSide View Connecting the drainReversingtheDoor Swing Bottom Hinge Top HingeTo reverse the hinges To replace door on hingesMayHear Using Your ICE MakerUnderstandingHowYour Ice Maker Works Making IceCleaning ExteriorSurfaces Setting the ControlsCleaning the Condenser Cleaning the Ice Maker SystemCleaningthe Interior Components To shut down the ice maker For ice makers with a drain pump installedVacationandMovingCare Trouble Shooting Canada Assistance Or ServiceU.S.A Whirlpool will not pay for ONE-YEAR Full WarrantyFIVE-YEAR Full Warranty Votre sécurité et celle des autres est très importante Sécurité DE LA Machine À GlaçonsPièces ET Caractéristiques Espace requis Déballage delamachineà GlaçonsEnlèvement des matériaux d’emballage Nettoyage avant l’utilisationSpécificationsélectriques Méthode de mise à la terre recommandéeMised’aplombdelamachineà Glaçons Outillage requisLire toutes les instructions avec soin avant de commencer Raccordement delamachine àglaçons àl’alimentation eneauRaccordement du tuyau d’eau Ajustement deux pieds de nivellement avantVUE Avant VUE ArrièreVidange par gravité Raccordement de la vidangeVUE Latérale Système à pompe de vidange sur certains modèlesInversion des charnières DelaportePour retirer la porte des charnières Charnière supérieure Réinstallion de la porte sur les charnièresCharnière inférieure Inversion du loquet de porteFabrication de la glace GlaçonsNettoyage dessurfaces Extérieures Réglagedes commandesMachine À Glaçons Nettoyage du condenseur Machineà glaçonsNettoyage descomposants Intérieurs Machine à glaçons avec pompe de drainage Lesvacances oule DéménagementArrêt de la machine à glaçons La machine fonctionne, mais produit très peu de glace DépannageLa machine fonctionne, mais ne produit pas de glace Les glaçons ont un goûtAuxÉtats-Unis Assistance OU ServiceAuCanada Garantie Complète DE Cinq ANS Garantie Complète DE UN ANWhirlpool Corporation ne paiera pas pour Pour des renseignements sur la garantie au Canada2208357

2208357 specifications

The Whirlpool 2208357 is a highly regarded appliance that stands out in the world of refrigerators, particularly known for its adept design and a host of functional features aimed at enhancing the user experience. This refrigerator exemplifies Whirlpool's commitment to quality and innovation, offering consumers a blend of style and practicality.

One of the primary features of the Whirlpool 2208357 is its spacious interior, designed to accommodate a variety of food items. This refrigerator boasts adjustable shelves, allowing users to customize the interior layout according to their storage needs. The flexible storage options make it easy to store tall bottles or large containers without compromising space.

The refrigerator is also equipped with a sophisticated cooling system that ensures even temperature distribution. This technology prevents hotspots, helping to maintain the freshness of food items longer. Additionally, the presence of humidity-controlled crispers prolongs the lifespan of fruits and vegetables by regulating humidity levels, ensuring they remain fresh and crisp.

Energy efficiency is another hallmark of the Whirlpool 2208357. The appliance is designed to consume less electricity while delivering top-notch performance. This energy-efficient design not only helps in reducing utility bills but also reflects an eco-friendly commitment.

Moreover, the Whirlpool 2208357 features a user-friendly control panel, making it easy for users to adjust temperatures and settings with ease. The intuitive display provides quick access to various functions, enhancing the overall user experience.

In terms of design, the Whirlpool 2208357 offers a sleek and modern aesthetic that fits seamlessly into any kitchen decor. Available in various finishes, it can complement both contemporary and traditional kitchens. The appliance's door design also adds to its stylish appearance while ensuring durability.

Built with quality materials, the Whirlpool 2208357 promises longevity and reliability, catering to the needs of families and individuals alike. Its robust construction minimizes the chances of wear and tear, making it a worthwhile investment for any household.

In summary, the Whirlpool 2208357 is an exemplary refrigerator known for its spacious interior, advanced cooling technologies, energy efficiency, and user-friendly features. Its modern design combined with durability makes it a preferred choice for consumers looking for a reliable and stylish kitchen appliance.
Top Page Image Contents