Installation, Mounting height reference | Zephyr EBO-E42ASX manual

Installation	1.	If possible, disconnect and move freestanding or
	1.	If possible, disconnect and move freestanding or
		slide-in range from cabinet opening to provide easier
		access to rear wall. Otherwise put a thick, protective
		covering over countertop, cooktop or range to
		protect from damage or dirt. Select a flat surface for
		assembling the unit. Cover that surface with a
		protective covering and place all canopy hood parts
		and hardware in it.
	2.	Determine and mark the centerline on the wall where
		the canopy hood will be installed.
	3.	Select a mounting height comfortable for the user
		and mark on wall behind cooktop.
	4.	Tape template, matching center-line and hood
		bottom as shown in Figure below.
	5.	Place the lower support bracket on the template
		making it coincide with the traced triangle, mark
		center of two fastener location and one lower
		fastener location then remove template.

centerline

fasteners	C
locations	C	lower
	L	lower
		support
		bracket

mounting height reference

6.Mark wall with horizontal line 1" above highest and 1" below lowest fastener location.

7.Find studs behind drywall by tapping wall or using a stud finder. Mark the center of the studs with a vertical line to the right and left of the marked fastener location.

8.Note: all fastener location must span the studs otherwise proceed as follows:

Cutout drywall along marked lines. Install each necessary between studs firmly flush with already existing stud front. Make sure all mounting screws will anchor to added studs. Replace drywall and refinish.

9.Determine and make all necessary cuts in the wall for the vent system. Install the vent system before the canopy hood. See „Venting methods“ and „Dimensions and clearance“ paragraphs.

Note - for Ductless - recirculating - installations: Vent system is not required.

10.Determine the required height for the conduit and cut a 1-1/4" (3.2 cm) hole at this location.

Run wires through hole according the National Electrical Code or CSA Standards and local codes and ordinances.

Note: If a In-line blower installation is required/ needed, then provide an additional hole/conduit.

There must be enough power supply cable from the fused disconnect (or circuit breaker) box to make the connection in the hood’s Junction box/es.

Use caulking to seal all openings.

Do Not turn on power until installation is completed.

11.Remark center line and hood bottom on same location as before and tape template on wall as in step 4 above.

12.Mount the lower support bracket with wood screws (supplied in mounting hardware kit) on locations marked on template, then remove template.

13.Install duct cover support bracket to wall flush to ceiling with drywall anchors supplied (the duct cover support bracket should be installed about 1/8“ (3mm) away from the ceiling).

For Ductless (recirculating) installations

Install the deflector (available as an extra kit) under the duct cover support bracket.

14.Note: disregard this step if intending to install a in- line blower.

Purchase and install the Internal blower (see paragraph „Before installing the hood - Parts not supplied“ for model reference).

EBO-E42ASX, EBO-E36ASX specifications

The Zephyr EBO-E36ASX and EBO-E42ASX are advanced cooling solutions designed for commercial applications where energy efficiency, performance, and reliability are paramount. Both models offer superior features tailored for various industries, making them reliable choices for those seeking quality and durability in air conditioning technology.

One of the standout features of the EBO-E36ASX and EBO-E42ASX is their inverter-driven compressor technology. This innovation allows the units to adjust the compressor speed according to the cooling load, ensuring optimal performance while minimizing energy consumption. As a result, these models achieve higher Seasonal Energy Efficiency Ratios (SEER), significantly reducing electricity bills while also contributing to a more sustainable environment.

Both units are equipped with advanced air filtration systems. These systems incorporate multi-layer filters designed to capture airborne particulates, allergens, and pollutants. This feature not only enhances indoor air quality but also contributes to a healthier working environment, making the EBO models well-suited for offices, schools, and hospitals. The filters are easy to access and can be replaced or cleaned without hassle.

In terms of design, the EBO-E36ASX and EBO-E42ASX units come with compact dimensions, allowing for versatile installation options. They can be mounted in various orientations, fitting seamlessly into a range of architectural layouts. The exterior casing is crafted from durable materials, ensuring that the units withstand harsh weather conditions and maintain their aesthetic appeal over time.

Moreover, both models feature a quiet operation mode, a crucial aspect for environments where noise reduction is essential. Utilizing sound-dampening technologies, these units operate at low noise levels, contributing to a comfortable atmosphere in offices, restaurants, and homes.

Integration with smart home technologies is another remarkable characteristic of the EBO-E36ASX and EBO-E42ASX. They are compatible with various smart thermostats and can be controlled remotely through mobile applications. This feature enables users to monitor and adjust settings, ensuring optimal indoor comfort while maximizing energy efficiency.

Overall, Zephyr's EBO-E36ASX and EBO-E42ASX represent a blend of cutting-edge technology, efficient performance, and user-friendly design. Their commitment to energy efficiency, air quality, and quiet operation makes them exemplary options for those looking to enhance their indoor environments. With these models, Zephyr continues to push the boundaries of HVAC technology, ensuring comfort and sustainability in commercial and residential applications alike.