StreamLight MS2015 owner manual Operation, Faceplate Release

Page 9
•FACEPLATE RELEASE

OPERATION

SWITCHING THE UNIT ON/OFF Switch on the unit by pressing any

button (except OPEN/CLOSE button (7)). When system is on, press Manual background button

(9) to turn off the unit.

FACEPLATE RELEASE

Press OPEN/CLOSE button (7) to slide down the removable faceplate down.

SOUND ADJUSTMENT

Press PUSH SEL button (10) to select the desired adjustment mode.

The adjustment mode will change in

the following order:

 

VOL

 

 

 

BAS

 

 

 

TRB

 

 

 

BAL

 

 

 

FAD

 

 

(Volume)

 

 

(Bass)

 

 

(Treble)

 

 

(Balance)

 

 

(Fader)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

By rotating the volume knob (10) clockwise or counter-clockwise, it is possible to adjust the desired sound quality.

LOUDNESS

Press BND/LOU button (13) for several seconds to reinforce the bass output. Press it for several seconds again to release this function.

SET THE CLOCK

Press the DSP button (15), the clock is displayed on the LCD display. Then hold down the button until the clock

flashes. Then press the Manual background button (17)

to change hours or Manual background button (16) to change minutes.

MUTE

Press MUT button (3) to mute the volume instantly. If any button is pressed while in the mute mode, the mute function is released.

EQUALIZATION

Press EQ button (19) to turn on equalization function and to select

desired audio mode. There are four

kinds of mode as below:

Manual backgroundManual backgroundFLATManual backgroundCLASSICSManual backgroundPOP MManual backgroundROCK MManual backgroundDSP OFF Manual background

LIQUID CRYSTAL DISPLAY

Shows current frequency and activated functions on the display (8).

FLASHING LED

If the front panel does not install in the main unit, the LED (4) will be flashing.

REMOTE SENSOR

Point the remote control handset to the remote sensor IR (11). Press the function keys on the handset to control the system.

RESET FUNCTION

RESET button (12) must be activated with either a ball point pen or thin metal object. The RESET button (12) is to be activated for the following

reasons:

-Initial installation of the unit when all wiring is completed.

-All the function buttons do not operate.

-Error symbol on the display.

Note: If you press RESET button (12) and the unit still does not work, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel.

RADIO OPERATION

SWITCHING TO RADIO MODE Press MOD button (6) to select radio mode, the radio mode appears in the display together with the memory band and frequency.

SELECTING THE FREQUENCY BAND

In radio mode, press BND/LOU button (13) to select the desired band.

The reception band will change in the following order:

Manual backgroundFM1Manual backgroundFM2Manual backgroundFM3Manual backgroundAM

SELECTING STATION

Press Manual background button (17) or Manual background button (16) shortly to activate automatic seek function. Press for several seconds until “MANUAL” appears on the display, the manual tuning mode is selected. If Manual background buttons (16) and Manual background button (17) have not been pressed for serveral seconds, the unit returns to seek tuning mode and “AUTO” appears on the display.

LOCAL/DISTANT

Press LOC button (2) to select between local and distant stations. Local setting is for reception of strong stations and distant setting is for reception of weaker setting. This function is effect during AUTO SEEK operation.

AUTOMATIC MEMORY

STORING & PROGRAM SCANNING

-Automatic Memory Storing

Press AMS button (18) for several seconds, the radio searches from the current frequency and checks the signal strength until one cycle search is finished. Then the 6 strongest

9

Image 9
Contents Remote Control Slide Down Detachable Panel Preset EqualizationMobile Audio System MS2015CONTENTS INSTALLATION TAKE OUT SCREW BEFORE INSTALLATIONDIN FRONT-MOUNTMethod A INSTALLATION Removing the unitDashboard Tabs Screwdriver Sleeve INSTALLATION DIN REAR-MOUNTMethod BUSING THE DETACHABLE FRONT PANEL To Reinstall the Front PanelTo Detach the Front Panel MAIN UNIT WIRING CONNECTIONLOCATION OF KEYS OPERATIONFACEPLATE RELEASE OPERATIONOPERATION MP3 OPERATIONPREVIEWING ALL TRACKS OPERATIONOPERATION DISC NOTE A. Notes on discsC.Notes on MP3 files FUNCTION KEYS & CONTROL REMOTE CONTROL HANDSETGENERAL SPECIFICATIONCD PLAYER RADIOSymptom TROUBLE SHOOTINGSolution CauseError Code showing on display CauseRemedy GUIDE D’UTILISATION TélécommandeSystème de radio mobile Lecteur de disques compacts numériquesTABLE DES MATIÈRES RETIRER LES VIS AVANT L’INSTALLATION INSTALLATION DIN PAR L’AVANT MÉTHODE AINSTALLATION Retirer l’appareil INSTALLATIONINSTALLATION INSTALLATION DIN PAR L’ARRIÈRE MÉTHODE BRéinstaller la face amovible UTILISER LA FACE AMOVIBLEDégager la face amovible UNITÉ PRINCIPALE CONNEXION DES CÂBLESFONCTIONNEMENT EMPLACEMENT DES COMMANDESFONCTION DE RÉINITIALISATION ‘RESET’ SOUND ADJUSTMENTFONCTIONNEMENT METTRE L’APPAREIL EN MARCHE-ARRÊT‘ON/OFF’MONO/STÉRÉO OPERATIONFONCTIONNEMENT DU LECTEUR CD CHOISIR LES PISTESRÉPÉTER LA MÊME PISTE OPERATIONJOUER TOUTES LES PISTES EN MODE ALÉATOIRE CHOISIR LES PISTES À L’AIDE DE LA TOUCHE AMS/MP3C. Remarques relatives aux fichiers MP3 OPERATIONTÉLÉCOMMANDE GÉNÉRALES SPÉCIFICATIONSLECTEUR CD RADIOSolution GUIDE DE DÉPANNAGESymptôme CauseCodes d’erreur apparaissant à l’affichage SolutionERREUR Cause