Zephyr AK8300ASX, AK8200AS manual Operation, Electrical Requirements

Page 5

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

NOT FOR USE OVER AN OUTDOOR GRILL

CAUTION

To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages.

OPERATION

Always leave safety grilles and fi lters in place. Without these components, operating blowers could catch onto hair, fi ngers and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

-To contact a qualifi ed electrical installer.

-To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualifi ed electrician determine that the ground path is adequate.

Do not ground to a gas pipe.

Check with a qualifi ed electrician if you are not sure the range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269 ** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to Electrical Diagram on product.

AK8200AS - 710W, 5.95 Amps

AK8300ASX (CBI-290B / CBI-600B) - 217W, 1.85 Amps / 460W, 3.85 Amps

AK8300ASX (PBI-1100A / PBN-1000A/CBE-1000) - 780W, 6.55 Amps / 840W, 7.3 Amps

A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and install appropriate connector if necessary.

FEDERAL COMMUNICATION COMMISSION INTERFACE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help

Important Safety Notice

3

Image 5
Contents Use, Care, and Installation Guide Page Installation Table of ContentsFeatures & Controls MaintenanceTo Reduce the Risk of Range TOP Grease Fire Important Safety NoticeFederal Communication Commission Interface Statement OperationElectrical Requirements List MaterialsDuct pieces Equivalent number Total Length x used Installation Ducting Calculation SheetDucting Installation Mounting Height & ClearanceAK8200AS Vertical Ducting Horizontal DuctingSome Ducting Options InstallationDucting Options Specifications Cable Lock Installation ElectricalElectrical Before installing into cabinet. b Power PackRemove support screw from top of Power Pack For Remote Blower Preparation Instructions Turn to Installation Single and Dual Internal BlowersRemote Blower Preparation InstallationBlower On/Off Features & Controls Touch ControlsTouch Controls Features & ControlsRemote Control Features RF Remote ControlRemote Control Maintenance Follow instructions below for replacing batterySurface Maintenance Installing FiltersMaintenance Cleaning Replacing Light Bulbs Maintenance LightsIssue Cause What to do TroubleshootingTroubleshooting Procedures for Tornado II and Tornado Replacement Parts List of Parts and AccessoriesOptional Accessories DescriptionLimited Warranty

AK8300ASX, AK8200AS specifications

The Zephyr AK8200AS and AK8300ASX are two cutting-edge air conditioning systems that represent the pinnacle of modern HVAC technology. Designed for both residential and commercial applications, these models combine efficiency, performance, and user-friendly features to provide optimal indoor comfort.

One of the standout characteristics of the AK8200AS and AK8300ASX is their energy efficiency. Both models utilize advanced inverter technology, which allows the units to adjust their cooling capacity based on the real-time cooling demands of the space. This not only ensures consistent temperature control but also significantly reduces energy consumption, making them environmentally friendly and cost-effective.

In terms of cooling capacity, the AK8200AS boasts a robust output that makes it suitable for medium-sized rooms, while the AK8300ASX is designed for larger spaces, providing an even higher capacity. This flexibility allows users to select the model that best meets their specific needs.

Another key feature of these air conditioning systems is the whisper-quiet operation. Thanks to their sophisticated design and engineering, both units operate at a sound level that is unobtrusive, allowing for a peaceful environment ideal for resting, working, or entertaining.

The filtration systems in the AK8200AS and AK8300ASX are also noteworthy. They incorporate multi-layer filters that not only capture dust and allergens but also help to neutralize odors, ensuring that the air quality remains clean and fresh. This feature is particularly beneficial for individuals with respiratory issues or allergies.

User convenience is enhanced with the inclusion of smart technology integration. Both models are compatible with various smart home systems, allowing users to control their air conditioning remotely via smartphones or voice-activated devices. This added functionality provides the freedom to adjust settings, monitor energy usage, and receive maintenance reminders seamlessly.

In terms of design, the AK8200AS and AK8300ASX feature a sleek and modern aesthetic that complements a variety of interiors. Their compact size also allows for easy installation in various settings, including wall-mounted and ceiling-mounted options.

In conclusion, the Zephyr AK8200AS and AK8300ASX offer an impressive combination of energy efficiency, powerful cooling capacity, quiet operation, superior air filtration, and modern smart technology. These features not only enhance comfort but also contribute to a healthier indoor environment, making them a leading choice for consumers seeking reliable air conditioning solutions.