Rear Panel Features

CHAPTER 1

MANUFACTURED UNDER LICENSE
FROM DOLBY LABORATORIES.			AUDIO/VIDEO INPUTS					AUDIO/VIDEO OUTPUTS
"DOLBY", "PRO-LOGIC" AND THE
DOUBLE-D SYMBOL ARE
DOUBLE-D SYMBOL ARE		DVD	SAT	VID1	VID2	VCR	CD	MAIN	VCR VID2/MON2
TRADEMARKS OF DOLBY	S	DVD	SAT	VID1	VID2	VCR	CD	MAIN	VCR VID2/MON2
LABORATORIES.	S
VIDEO

Made in Snohomish, Washington, U.S.A.

RIGHTRIGHT

COMPONENT VIDEO IN			COMPONENT	TRIGGERS SURROUND	MAIN	CENTER
DVD	SAT	VID1	MAIN OUT MON2	12VDC

LEFT	LEFT
MAIN	SURROUND

75 Ω

COMP

DVD

SAT

VID1

VID2

VCR

MAIN

VCR

VID2/MON2

VIDEO

GND

DVD

SAT

VID1

VID2

VCR

MAIN

VCR

VID2/MON2

MANUFACTURED UNDER LICENSE

FROM DIGITAL THEATER SYSTEMS,

INC. US PAT. NO. 5,451,942,

AUDIO INPUTS

AUDIO OUTPUTS

8-CHANNEL INPUTS

5,956,674, 5,974,380, 5,978,762 AND

OTHER WORLD-WIDE PATENTS

ISSUED AND PENDING. "DTS",

PHONO

DAT

TAPE

DAT

TAPE

LEFT

L SUR

CEN

LB SUR

"DTS-ES EXTENDED SURROUND"

AND "NEO:6" ARE TRADEMARKS

OF DIGITAL THEATER SYSTEMS,

DIGITAL THEATER SYSTEMS, INC.

PHONO

DAT

TAPE

DAT

TAPE

RIGHT

R SUR

SUB

RB SUR

			Cr		MAINZONE	12VDC
			Cb		ZONE2	12VDC
DIGITAL AUDIO INPUTS
DVD	SAT	VID1	CD	DVD	SAT	VID1
DVD	SAT	VID1	CD
				CD	DAT	VID2
STEREO OUTPUTS				LINE LEVEL AUDIO OUTPUTS
FIXED MAIN ZONE2			LEFT	LEFT SUR	CENTER	SUB2
		L
		R
FIXED MAIN ZONE2			RIGHT	RIGHT SUR	SUB1	SUB3

SPEAKER LEVEL AUDIO OUTPUTS

	Sunfire	RS-232
	Sunfire
Ultimate Receiver II
	DIGITAL OUT	IEEE
		1394
LB SUR	SIDES	I R
LB SUR	L SIDE AXIS	MAIN
		REPLACE WITH ORIGINAL
		FUSE TYPE AND RATING
RB SUR	R SIDE AXIS	ZONE2

AC FUSE

SURROUND

RIGHT BACK LEFT

OPTIONAL:

SIDE-AXIS

ZONE2

AC INPUT

120 VAC 60 Hz

1112

1.Audio/Video Inputs

These audio, composite-video and S-video inputs connect to the outputs of your audio video com- ponents. When these inputs are selected, the audio will be heard in your system and the video will be seen on the TV screen. VID2 can be used for a second VCR.

2. Audio/Video Outputs

MAIN: connects to the inputs of a TV monitor, where the video of any selected input and the On Screen Display (OSD) can be viewed. The audio connec- tions allow you to listen to any selected audio source through your TV’s speakers.

VCR: connects to the inputs of a VCR to allow recording.

VID2/MON2: connects to the input of a second VCR for recording, or to a second TV. When con- Þgured in the OSD for “VID2,” this output is muted whenever the VID2 input is selected. This prevents feedback; also there is no OSD then on this output. When conÞgured for “MON2,” the output is always active, the same as the Main output.

14 15

Note: Analog audio signals are present at these L and R outputs even if a digital input has been selected. The output is a 2 chan- nel downmix if the digital source is more than 2 channels.

3. Component Video In

These inputs connect to the component video outputs of your DVD, SAT or other video source (VID1) if they have this advanced capability. When these inputs are selected, the Receiver's Pro- cessor will automatically route any video signals going into these jacks to the component video outputs. Note that component video provides the best picture compared to composite or S-video. The Receiver can also switch HDTV signals.

4. Component Video Out

If your TV Monitor has component video inputs, connect them to these outputs. If you select DVD, SAT or VID1, then any video sig- nals going to the component inputs, will pass through to your TV monitor.

17 1819 20 21

5. Triggers and Relay

The relay switch is normally open, and it will close after a short delay, when selecting a source. This can be used in installations to trigger video screen deployment, or other custom purposes. The OSD INPUTS menu lets you choose which inputs activate the relay.

The +12 VDC outputs are on whenever their zone is enabled. They can be used to automatically turn on ampliÞers for example. The 1/8” mini-jack is wired in parallel with the terminals. Do not exceed a current draw of 500mA total for both outputs.

6. Speaker-level Outputs

These speaker-level audio out- puts connect to the inputs of your speakers. The outputs are: front left, front right, center, left sur- round, and right surround. The two lower (Aux) outputs can be assigned as surround back out- puts, Zone 2 outputs or side-axis outputs, see page 41 for details.

User's Manual