Sunfire Radio manual Recording to a Tape Player, Recording to a VCR

CHAPTER 5

Recording

Recording to a Tape Player

Input signals from an audio source playing in the Receiver can be recorded using the left and right audio outputs. The Tape player will receive a straight copy of the analog source signal going in, unaffected by the volume, tone or any sur- round modes. If you are playing a digital source,

VCR

VID2/MON2

L

R

AUDIO

INPUTS

R

PHONO

AUDIO

DAT

TAPE

OUTPUTS

L

DAT

8-CHANNEL

TAPE

LEFT

INPUTS

L SUR

L

CEN

LB SUR

R

R

PHONO

DAT

TAPE

DAT

TAPE

RIGHT

R SUR

SUB

RB SUR

RECORD

From Receiver

TAPE outputs

				Cb
DIGITAL
		AUDIO
DVD		SAT	INPUTS
			VID1	CD
STEREO		OUTPUTS
FIXED
	MAIN ZONE2			LEFT
			L
			R
FIXED
	MAIN ZONE2			RIGHT

	ZONE2
DVD				SPEAKER LEVE
	SAT
			VID1	Ultim
CD	DAT				DI
			VID2
LINE LEVEL		AUDIO
LEFT SUR			OUTPUTS
	CENTER
			SUB2	LB
				SUR	L
RIGHT SUR		SUB1
			SUB3
				RB SUR
					R

the tape player will receive a downmixed stereo analog signal for recording.

PLAY

To Receiver TAPE inputs

•Turn OFF the Fully Automatic mode. This is because some Tape decks, such as three-head decks, will have an output signal going into the Receiver during recording. The DAT or TAPE inputs may be incorrectly selected as an input, rather than the source you are trying to record.

•Manually select the source such as CD and play it through your system.

•Set your Tape player to record, and adjust the input levels for the best performance. Once the levels are correct, you can reset your source to the beginning and make your recording.

•Do not select another Main Zone input while you are recording.

Recording to a VCR

Any video source playing in the Receiver can be recorded using the left and right audio and the video outputs. The VCR will receive a straight copy of the source signal going in, unaffected by the volume, tone or any surround modes.

• Select the video source and play it

FM 75 Ω

GND AM

S	DVD	AUDIO/VIDEO
VIDEO		SAT		VID1
COMP	DVD	SAT
VIDEO				VID1
	DVD	SAT		VID1
L
R
	AUDIO		INPUTS
	PHONO
		DAT		TAPE
L
R
PHONO		DAT		TAPE

INPUTS	VCR				AUDIO/VIDEO
VID2		CD						OUTPUTS
					MAIN	VCR
								VID2/MON2
VID2	VCR	CD
					MAIN
						VCR
								VID2/MON2
VID2	VCR	CD
					MAIN
						VCR		VID2/MON2
			L
			R
AUDIO	OUTPUTS
DAT				8-CHANNEL
	TAPE		LEFT				INPUTS
					L SUR
L							CEN		LB SUR
R
DAT	TAPE
		RIGHT
					R SUR		SUB
									RB SUR

	Made in
COMPONENT		Snohomish,	U.S.A.
		VIDEO IN
DVD	SAT		COMPONENT
		VID1			TRIGGERS
			MAIN OUT M	ON2		RIGHT
					12VDC	SURROUND	RIGHT
		Y					MAIN

				Cr
				Cb
DIGITAL
		AUDIO
DVD		SAT	INPUTS
			VID1
				CD
STEREO		OUTPUTS
FIXED
	MAIN ZONE2			LEFT
			L
			R
FIXED
	MAIN ZONE2			RIGHT

ZONE2 MAIN ZONE

				SPEAKER
DVD				LEVEL AU
	SAT		VID1			Sun
				Ultim
CD						ate R
	DAT				D	IGITA
			VID2
LINE LEVEL		AUDIO
LEFT SUR			OUTPUTS
	CENTER
			SUB2	LB SUR		SID
					L SIDE
RIGHT SUR		SUB1
			SUB3
				RB SUR
						R SIDE

through your system.

• Set your VCR to record.

• Do not select another Main Zone source

while you are recording.

• The VID2/MON2 output can also be used

for recording, but Þrst make sure that it

is set to VID2 in the VIDEO menu of the

OSD (see page 37). This output will then

mute to prevent feedback whenever the

VID2 input source is selected.

• Do not use the OSD while recording, as

the incoming video is shut off while the

OSD is displayed

46

RECORD

From Receiver

VCR outputs

PLAY

To Receiver

VCR inputs

User's Manual