Sunfire TGP-5(E) manual RS-232 Port

Page 51

APPENDIX

The RS-232 Port

The TGP-5 has a rear panel RS-232 Serial communication port. This allows the FLASH memory to be upgraded to the latest software by connecting to a PC.

The TGP-5 software may be updat- ed to refine operational details and to include new features. Downloadable updates will be posted on our website: www.sunfire.com.

Communications

Serial RS-232, 9600 Baud, 8-N-1

DB-9 Wiring

PINS 1, 6 and 4 are joined together internally

PINS 7 and 8 are joined together internally

PIN 2- Data from TGP-5 to controller (TGP-5 transmit)

PIN 3- Data from controller to TGP-5 (TGP-5 receive)

PIN 5- Ground/Common PIN 9- No connection

The RS-232 connector is female.

Serial Cable

To connect the TGP-5 port to a computer, you will need a "straight- through" serial cable. This has con- nector pins at one end connected directly to the pins of the connector at the other end. For example, pin 1 at one end connects to pin 1 at the other end, pin 2 connects to pin 2, pin 3 to pin 3 and so on.

These common cables are avail- able from most computer stores (or from Radio Shack as # 26-117). It should be 9-pin male at one end, to fit into the TGP-5 and normally 9-pin female at the other, to fit into your computer's serial port (COM1 or COM2).

User's Manual

Update Procedure

1.The current version level of the software running your TGP-5 can be found by looking at the Version Level OSD menu. This is under the Software OSD menu (see page 37).

2.Downloadable updates are on our website www.sunfire.com. If the website file is newer than your current version, follow the website directions and down- load the new file onto your computer's hard drive.

3.Record your calibration, preset stations or other settings on page 57. In most cases, the upgrade will not affect any of these settings, but it is good to record them just in case.

4.Turn off your computer and the TGP-5. Position them close enough so that they can be easily connected using your serial cable. If you have a lap- top computer, then it may be easier to bring that close to the TGP-5. Otherwise, you need to disconnect the TGP-5 and move it close to your computer.

5.Connect the TGP-5 RS-232 port to the corresponding serial port on your computer.

6.Turn on the TGP-5 and your computer.

7.Find the file you downloaded in step 2, and run the program.

8.In AUTO mode, the software will look for an active serial connection and upload the new file. The TGP-5 display will show the status.

9.When the file transfer is com- plete, press the Power switch on the TGP-5 front panel. This completes the upgrade.

10.Turn off your computer and the TGP-5, and disconnect the se- rial cable.

External Control

The RS-232 port also allows the TGP-5 to be controlled externally by Home Theater controllers and com- puters.

Serial command set

The following information is for programmers and developers:

Contact Sunfire Technical Support, or our website www.sunfire.com for a list of serial commands.

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Theater Grand Processor Important Safety Instructions NEC National Electrical Code Contents Introduction Remote Features UnpackingFeaturesMain OverviewExit Quick Start GuideFurther Information Display Front Panel FeaturesPower Mode ButtonsTone Controls VolumeLock Indicators Tuner ControlsRear Panel Features Ground Screw Power SwitchFM Antenna AM AntennaInstallation Analog audio and composite video System ConfigurationsHdmi OUT Digital audio and component video connectionsRF demodulator LD connections external RF Demodulator and S-VideoDVD VCR connections analog audio and composite videoAM Loop Antenna CD and Antenna connectionsTurntable connections Tape Player connections Channel Input connections analog audio Speakers Amplifier connectionsZone 2 connections Remote Control Zone Operating the TGP-5 with the RemotePRO Remote SetupLearn Remote SetupMacro Recal RecallMain MON2 On Screen Display OSDOSD Activation Quick InformationOSD Menus Trim and Tone Menus Tone MenuTrim Menu Modes Menu Input Menus Input Configuration MenusInput Menus Tuner Preset Menus Tuner Preset MenuPreset procedure Main Zone and Zone 2 Menu Zone 2 MenuMain Zone Menu Control Menu Video, Software and Control MenusVideo Menu Software MenuSpeaker Size Menu Speaker Size MenuSpeaker Position Menu Speaker Calibration Speaker Calibration MenuSurr Crossover Crossover adjustment Subwoofer ModeSpeaker Crossover Menu CrossoverVideo Conversion Bass Management Using the TGP-5Source Direct Surround Modes for 2-Channel SourcesStereo Dolby PRO Logic Party Jazz ClubDolby Digital Surround Modes for Multi-Channel SourcesTuner Operation Recording Recording to a Tape PlayerRecording to a VCR Turning on Zone IndicatorsZone 2 Operation ConnectionsSoftware Upgrade Software Revision List Sonic HolographySoftware CD Center speaker Speaker PlacementAppendix Front SpeakersSurround Back Speakers Side-Axis SpeakersSurround Speakers Subwoofer LocationRS-232 Port No sound from one or more speakers Troubleshooting GuideNo Tone Controls Your amplifiers shut down often Audio Components Remote Control CodesTape Decks Video Settings Tone SettingsZone Settings Input Settings Mode SettingsSpecifications Service Assistance Limited WarrantyTGP-5 Addendum

TGP-5(E), TGP-5 specifications

The Sunfire TGP-5 and TGP-5(E) are high-end audio processors that cater to audiophiles and home theater enthusiasts seeking exceptional sound quality and advanced features. These models are designed with a commitment to delivering pristine audio performance across various formats, making them ideal for both music and movie playback.

One of the standout features of the TGP-5 is its robust digital signal processing capabilities. The device is equipped with a state-of-the-art multichannel DAC that ensures accurate sound reproduction and a high signal-to-noise ratio. This component allows for the processing of high-resolution audio formats, including DSD, ensuring that users can enjoy their music as intended by the artist. The TGP-5(E) version further enhances this experience by offering enhanced room correction technology, which automatically calibrates the system based on the specific acoustics of the listening environment. This feature optimizes audio performance by adjusting frequency response, thereby eliminating unwanted resonances and improving overall sound clarity.

The user interface of the TGP-5 series is designed for ease of use, featuring a straightforward menu system accessible via its front panel display or remote control. Connections are abundant, offering a variety of digital inputs, including HDMI, coaxial, and optical, alongside traditional analog RCA inputs. These options ensure compatibility with almost any home theatre setup and allow integration with modern streaming services and devices.

Another noteworthy characteristic is the TGP-5's support for surround sound formats, including Dolby Atmos and DTS:X. This capability allows users to create an immersive audio experience that enhances movie watching and gaming sessions. Additionally, the TGP-5 incorporates advanced connectivity options, such as Bluetooth and Wi-Fi, enabling wireless streaming from smartphones and tablets.

In terms of build quality, the Sunfire TGP-5 series boasts a sleek and elegant design, typically encased in a sturdy chassis that minimizes vibration and interference. This construction not only enhances durability but also adds a touch of sophistication to any audio setup.

In summary, the Sunfire TGP-5 and TGP-5(E) represent a blend of cutting-edge technology, exceptional audio fidelity, and user-friendly features. With their advanced processing capabilities, comprehensive connectivity options, and support for modern audio formats, these processors are a compelling choice for anyone looking to elevate their audio experience.
Top Page Image Contents